参数资料
型号: MCZ33927EK
厂商: Freescale Semiconductor
文件页数: 32/44页
文件大小: 0K
描述: IC FET PRE-DRIVER 3PH 54-SOIC
标准包装: 26
配置: 3 相桥
输入类型: 反相和非反相
延迟时间: 265ns
电流 - 峰: 600mA
配置数: 1
输出数: 3
高端电压 - 最大(自引导启动): 75V
电源电压: 8 V ~ 40 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 54-BSSOP(0.295",7.50mm 宽)裸露焊盘
供应商设备封装: 54-SOICW-EP
包装: 管件
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
DEADTIME COMMAND
Deadtime prevents the turn-on of both transistors in the
same phase until the deadtime has expired. The deadtime
timer starts when a FET is commanded off (see Figure 6 and
Figure 11 ). The deadtime control is disabled by enabling the
FULLON mode.
The deadtime is set by sending the DEADTIME command
(100x xxx1), and then sending a calibration pulse of CS. This
pulse must be 16 times longer than the required deadtime
(see Figure 16 ). Deadtime is measured in cycle times of the
internal time base, f TB . This measurement is divided by 16
and stored in an internal register to provide the reference for
timing the deadtime between high and low gate transactions
in the same phase.
For example: the internal time base is running at 20MHz
and a 1.5 μs deadtime is required. First a DEADTIME
command is sent (using the SPI), then a CS is sent. The CS
pulse is 16*1.5=24 μs wide. The IC measures this pulse as
24000ns/50ns = 480 clock cycles and stores 480/16=30 in
the deadtime register. Until the next deadtime calibration is
Table 13. .DEADTIME Command
performed, 30 clock cycles will separate the turn off and turn
on gate signals in the same phase. The worst case error
immediately after calibration will be +0/-1 time base cycle, for
this example +0ns/-50ns. Note that if the internal time base
drifts, the effect on dead time will scale directly.
Sending a ZERO DEADTIME command (100x xxx0) sets
the deadtime timer to 0. However, simultaneous turn-on of
high-side and low-side FETs in the same phase is still
prevented unless the FULLON command has been
transmitted. There is no calibration pulse expected after
receiving the ZERO DEADTIME command.
After RESET, deadtime is set to the maximum value of 255
time base cycles (typically 15 μs).
The IC ignores any SPI data that is sent during the
calibration pulse. If there are any transitions on SI or SCLK
while the Deadtime CS pulse is low, a Framing Error will be
generated, however, the CS pulse will be used to calibrate
the deadtime
SPI Data Bits
Write
7
1
6
0
5
0
4
x
3
x
2
x
1
x
0
ZERO/
CALIBRATE
Reset
x
x
x
x
Deadtime Calibration Pulse
CS
SCLK
DEADTIME
SI
Command
SO
Figure 16. Deadtime Calibration
33927
Analog Integrated Circuit Device Data
32
Freescale Semiconductor
相关PDF资料
PDF描述
MCZ33937EKR2 IC PRE-DRIVER 3PHASE 54-SOIC
MDN2BL3GRAS MOTOR BRUSHED DC 2V 2753RPM
MDN3BL3CSAS MOTOR BRUSHED DC 2V 1458RPM
MIC2287-34YML TR IC LED DRIVER WHITE BCKLGT 8-MLF
MIC2289C-34YD6 TR IC LED DRIVR WHITE BCKLGT TSOT-6
相关代理商/技术参数
参数描述
MCZ33927EK/R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three-Phase Field Effect Transistor Pre-Driver
MCZ33927EKR2 功能描述:功率驱动器IC THREE PHASE PRE- DRIVER RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MCZ33927R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three-Phase Field Effect Transistor Pre-Driver
MCZ33937AEK 功能描述:马达/运动/点火控制器和驱动器 3 Phase Pre-Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MCZ33937AEK/R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three Phase Field Effect Transistor Pre-driver