- 您现在的位置：买卖IC网 > PDF目录1954 > MCZ33972EWR2 (Freescale Semiconductor)IC SWITCH DETECTION MULT 32-SOIC PDF资料下载
参数资料
| 型号： | MCZ33972EWR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 11/32页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH DETECTION MULT 32-SOIC |
| 标准包装： | 1,000 |
| 应用： | 开关监控 |
| 接口： | SPI |
| 电源电压： | 8 V ~ 26 V |
| 封装/外壳： | 32-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 32-SOIC |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
33972
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
EXAMPLE OF NORMAL MODE OPERATION
The operation of the device in Normal mode is defined by
the states of the programmable internal control registers. A
typical application may have the following settings:
Programmable switch – set to switch-to-ground
All inputs set as wake-up
Wetting current on (16 mA)
Wetting current timer on (20 ms)
All inputs tri-state-disabled (comparator is active)
Analog select 00000 (no input channel selected)
With the device programmed as above, an interrupt will be
generated with each switch contact change of state (open-to-
close or close-to-open) and 16 mA of contact wetting current
will be source for 20 ms. The INT pin will remain LOW until
switch status is acknowledged by the microprocessor. It is
critical to understand INT will not be cleared on the rising
edge of CS if a switch closure occurs while CS is LOW. The
maximum duration a switch state change can exist without
acknowledgement depends on the software response time to
the interrupt. Figure 6, page 9, shows the interaction
between changing input states and the INT and CS pins.
If desired the user may disable interrupts (wake up/
interrupt command) from the 33972 device and read the
switch states on a periodic basis. Switch activation and
deactivation faster than the MCU read rate will not be
acknowledged.
The 33972 device will exit the Normal mode and enter the
Sleep mode only with a valid sleep command.
SLEEP MODE
Sleep mode is used to reduce system quiescent currents.
Sleep mode may be entered only by sending the sleep
command. All register settings programmed in Normal mode
will be maintained in Sleep mode.
The 33972 will exit Sleep mode and enter Normal mode
when any of the following events occur:
Input switch change of state (when enabled)
Interrupt timer expire
Falling edge of WAKE
Falling edge of INT (with VDD = 5.0 V and WAKE at
Logic [1])
Falling edge of CS (with VDD = 5.0 V)
Power-ON Reset (POR)
The VDD supply may be removed from the device during
Sleep mode. However removing VDD from the device in Sleep
mode will disable a wake-up from falling edge of INT and CS.
Note In cases where CS is used to wake the device, the
first SO data message is not valid.
The sleep command contains settings for two
programmable timers for Sleep mode, the interrupt timer and
the scan timer, as shown in Table 18 The interrupt timer is
used as a periodic wake-up timer. When the timer expires, an
interrupt is generated and the device enters Normal mode.
Note The interrupt timer in the 33972 device may be
disabled by programming the interrupt bits to logic [1 1 1].
Table 19 shows the programmable settings of the Interrupt
timer.
Table 16. Serial Output (SO) Bit Data
Type of Input
Input
Programmed
Voltage on
Input Pin
SO SPI Bit
SP
Switch to Ground
SPn < 4.0V
1
Switch to Ground
SPn > 4.0V
0
Switch to Battery
SPn < 4.0V
0
Switch to Battery
SPn > 4.0V
1
SG
N/A
SGn < 4.0V
1
N/A
SGn > 4.0V
0
Table 17. Serial Output (SO) Response Register
SO Response Will
Always Send
them
flg
int
flg
SP7
SP6
SP5
SP4
SP3
SP2
SP1
SP0 SG13 SG12 SG11 SG10 SG9 SG8 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0
Table 18. Sleep Command
Sleep Command
Command Bits
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1
0
X
int
timer
int
timer
int
timer
scan
timer
scan
timer
scan
timer
相关PDF资料 |
PDF描述 |
|---|---|
| MCZ33975AEKR2 | IC SWITCH DETECT MULT ENH 32SOIC |
| MCZ33993EWR2 | IC MULTIPLE SWITCH DETECT 32SOIC |
| MCZ79076EGR2 | IC IGNITION CTRL ELECTR 16-SOIC |
| MIC2070-2PCQS TR | IC USB PWR CTRLR DUAL 16-QSOP |
| MIC2550ABTS TR | IC USB TRANSCEIVER 14-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33972TEW | 制造商:Freescale Semiconductor 功能描述:MULTI-SW DETECT W/SUPRES - Bulk |
| MCZ33972TEW/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Multiple Switch Detection Interface with Suppressed Wake-up |
| MCZ33972TEWR2 | 制造商:Freescale Semiconductor 功能描述:MULTI-SW DETECT W/SUPRES - Tape and Reel |
| MCZ33975AEK | 功能描述:输入/输出控制器接口集成电路 ENHANCED MULTI SW DETECT RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| MCZ33975AEKR2 | 功能描述:接口 - 专用 ENHANCED MULTI SW DETECT RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。