- 您现在的位置：买卖IC网 > PDF目录22295 > MDC3105LT1G (ON Semiconductor)IC RELAY/DRVR INDUCT LOAD SOT23 PDF资料下载
参数资料
| 型号： | MDC3105LT1G |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/14页 |
| 文件大小： | 0K |
| 描述： | IC RELAY/DRVR INDUCT LOAD SOT23 |
| 标准包装： | 1 |
| 类型： | 继电/负载驱动器 |
| 输入类型： | 非反相 |
| 输出数： | 1 |
| 电流 - 输出 / 通道： | 400mA |
| 电流 - 峰值输出： | 500mA |
| 电源电压： | 6V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-236-3，SC-59，SOT-23-3 |
| 供应商设备封装： | SOT-23-3（TO-236） |
| 包装： | 标准包装 |
| 产品目录页面： | 1118 (CN2011-ZH PDF) |
| 其它名称： | MDC3105LT1GOSDKR |
MDC3105
Using TTR Designing for Pulsed Operation
For a repetitive pulse operating condition, time averaging
allows one to increase a device’s peak power dissipation
rating above the average rating by dividing by the duty cycle
of the repetitive pulse train. Thus, a continuous rating of 200
mW of dissipation is increased to 1.0 W peak for a 20% duty
cycle pulse train. However, this only holds true for pulse
widths which are short compared to the thermal time
constant of the semiconductor device to which they are
applied.
For pulse widths which are significant compared to the
thermal time constant of the device, the peak operating
condition begins to look more like a continuous duty
operating condition over the time duration of the pulse. In
these cases, the peak power dissipation rating cannot be
merely time averaged by dividing the continuous power
rating by the duty cycle of the pulse train. Instead, the
average power rating can only be scaled up a reduced
amount in accordance with the device’s transient thermal
response, so that the device’s max junction temperature is
not exceeded.
Figure 12 of the MDC3105 data sheet plots its transient
thermal resistance, r(t) as a function of pulse width in ms for
various pulse train duty cycles as well as for a single pulse
and illustrates this effect. For short pulse widths near the left
side of the chart, r(t), the factor, by which the continuous
duty thermal resistance is multiplied to determine how much
the peak power rating can be increased above the average
power rating, approaches the duty cycle of the pulse train,
which is the expected value. However, as the pulse width is
increased, that factor eventually approaches 1.0 for all duty
cycles indicating that the pulse width is sufficiently long to
appear as a continuous duty condition to this device. For the
MDC3105LT1, this pulse width is about 100 seconds. At
this and larger pulse widths, the peak power dissipation
capability is the same as the continuous duty power
capability.
To use Figure 12 to determine the peak power rating for
a specific application, enter the chart with the worst case
pulse condition, that is the max pulse width and max duty
Also note that these calculations assume a rectangular
pulse shape for which the rise and fall times are insignificant
compared to the pulse width. If this is not the case in a
specific application, then the V O and I O waveforms should
be multiplied together and the resulting power waveform
integrated to find the total dissipation across the device. This
then would be the number that has to be less than or equal
to the Pd(pk) calculated above. A circuit simulator having a
waveform calculator may prove very useful for this purpose.
Notes on SOA and Time Constant Limitations
Figure 10 is the Safe Operating Area (SOA) for the
MDC3105. Device instantaneous operation should never be
pushed beyond these limits. It shows the SOA for the
Transistor “ON” condition as well as the SOA for the Zener
during the turn ? off transient. The max current is limited by
the Izpk capability of the Zener as well as the transistor in
addition to the max input current through the resistor. It
should not be exceeded at any temperature. The BJT power
dissipation limits are shown for various pulse widths and
duty cycles at an ambient temperature of 25 ° C. The voltage
limit is the max V CC that can be applied to the device. When
the input to the device is switched off, the BJT “ON” current
is instantaneously dumped into the Zener diode where it
begins its exponential decay. The Zener clamp voltage is a
function of that BJT current level as can be seen by the
bowing of the V Z versus I Z curve at the higher currents. In
addition to the Zener’s current limit impacting this device’s
500 mA max rating, the clamping diode also has a peak
energy limit as well. This energy limit was measured using
a rectangular pulse and then translated to an exponential
equivalent using the 2:1 relationship between the L/R time
constant of an exponential pulse and the pulse width of a
rectangular pulse having equal energy content. These L/R
time constant limits in ms appear along the V Z versus I Z
curve for the various values of I Z at which the Pd lines
intersect the V CC limit. The L/R time constant for a given
load should not exceed these limits at their respective
currents. Precise L/R limits on Zener energy at intermediate
current levels can be obtained from Figure 11.
cycle and determine the worst case r(t) for your application.
Then calculate the peak power dissipation allowed by using
the equation,
Pd(pk) = (T Jmax ? T Amax ) ÷ (R q JA * r(t))
Pd(pk) = (150 ° C ? T Amax ) ÷ (556 ° C/W * r(t))
Thus for a 20% duty cycle and a PW = 40 ms, Figure 12
yields r(t) = 0.3 and when entered in the above equation, the
max allowable Pd(pk) = 390 mW for a max T A = 85 ° C.
http://onsemi.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5190YMM TR | IC REG CTRLR SGL POS ADJ 10-MSOP |
| MIC5157YN | IC REG CTRLR SGL OUT 14-DIP |
| MIC5156YM | IC REG CTRLR SGL POS ADJ 8-SOIC |
| NLC565050T-2R7K-PF | INDUCTOR POWER 2.7UH 1.2A 2220 |
| MIC5156-3.3YM | IC REG CTRLR SGL 3.3V 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MDC3105LT1G-CUT TAPE | 制造商:ON 功能描述:MDC3105 Series 6 V 400 mA Integrated Relay Inductive Load Driver SOT-23-3 |
| MDC-316 | 制造商:POWER DYNAMICS 功能描述:6PIN MINI DIN FULLY SHLDD |
| MDC320-49TG.1 | 制造商:Advanced Interconnect 功能描述: |
| MDC3205 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:RELAY/SOLENOID DRIVER SILICON MONOLITHIC CIRCUIT BLOCK |
| MDC-321-PLAIN-ALUM | 功能描述:罩类、盒类及壳类产品 CONS DESKTOP PL ALUM RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
发布紧急采购，3分钟左右您将得到回复。