参数资料
型号: MDEV-433-HH-KF-MS
厂商: Linx Technologies Inc
文件页数: 2/7页
文件大小: 0K
描述: KIT MASTER DEV MS KEYFOB 433MHZ
产品变化通告: Keyfob Part Number Change 05/Aug/2011
标准包装: 1
系列: MS
类型: 发射器
频率: 433MHz
适用于相关产品: MS 遥控钥匙系列 - 433MHz
已供物品: 板,2 个发射器,2 个接收器,2 个解码器,天线,CD
其它名称: MDEV-433-HH-KF5-MS
MDEV-433-HH-KF5-MS-ND
MS SERIES DECODER DEVELOPMENT BOARD
USING THE MASTER DEVELOPMENT SYSTEM
Using the Master Development System is straightforward. After unpacking the
board, screw the antenna onto the connector, install the supplied 9V battery, and
1
5
9
8
turn on the power switch. The encoder and decoder will have default settings
from the factory and will work straight out of the box. To create a new address,
follow these easy steps:
1. Press and hold the CREATE_ADDR button on the transmitter to create a new
Code Word. This is done by sticking a paper clip through the hole on the back
of the case and pressing the button inside. The Code Word will be randomized
for as long as the button is held down. Once comfortable that the number is
sufficiently random, release the button.
2
6
7
11
10
12
2. Once the button is released, the MODE_IND LED will begin to flash to indicate
that it is ready to accept Control Permissions. Press all of the data line buttons
that are to be recognized, then press the CREATE_ADDR button again or let it
time out after seventeen seconds.
3. Press the LEARN button on the decoder board and the MODE_IND LED will
4
13
14
start flashing. Press any of the data line buttons on the transmitter and press the
LEARN button again. The encoder’s Code Word has now been learned by the
decoder and they will operate together.
3
Figure 1: The MS Series Decoder Development Board
TROUBLESHOOTING
If the boards fail to work out of the box, then try the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
9V Battery
Power Jack
On-Off Switch
Voltage Regulator
QS Series USB Module
Prototype Area
Break-out Header
RP-SMA Antenna Connector
LR Series Receiver
MS Series Decoder
Data Line LEDs
? Check the battery to make sure it is not dead.
? Make sure the baud rate switches are set to 9,600bps on the decoder board.
? Make sure that the antenna is connected.
? Check to see if the PDN switch is on, placing the decoder into Power Down
Mode. In most cases, the encoder PDN switch should be on.
? Make sure that you set your Control Permissions correctly. If you have not set
the encoder to use a particular line, then when you press a button on the
encoder board, the MODE_IND LED on the decoder board will light up, but the
data line LED will not light up.
If all of these appear to be in order, then you can call 800-736-6677 or e-mail
techsupport@linxtechnologies.com for technical support.
12.
13.
14.
Page 2
Indicator LEDs
Function Switches
LEARN Button
Page 3
相关PDF资料
PDF描述
IXTY12N06T MOSFET N-CH 60V 12A TO-252
EVAL-433-LR KIT BASIC EVAL 433MHZ LR SERIES
EVAL-418-HHLR KIT EVAL FOR HHLR 418MHZ XMITTER
MDEV-433-HH-LR8-HS KIT DEV TX 433MHZ HS LONG-RANGE
PM113-625.0M OSC 625.0000 MHZ 3.3V LVPECL
相关代理商/技术参数
参数描述
MDEV-433-HH-LR8-HS 功能描述:射频开发工具 HS LongRange Handhld Trans Dev Sys 433MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MDEV-433-HH-LR8-MS 功能描述:射频开发工具 MS LongRange Handhld Trans Dev Sys 433MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MDEV-433-RM 功能描述:KIT MASTER EVAL 433MHZ RM SERIES RoHS:否 类别:RF/IF 和 RFID >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:用于 200/300 系列的欧盟开发套件 适用于相关产品:Zensys RF 模块 所含物品:开发板,模块,编程器,软件,线缆,电源 其它名称:703-1019Q3225667
MDEV-868-NT 功能描述:射频开发工具 NT Series Dev Kit w/ Transparent Module RoHS:否 制造商:Linx Technologies 产品: 类型: 工具用于评估: 频率: 工作电源电压:
MDEV-869-ES-RS232 功能描述:射频开发工具 ES Master Dev Sys 869MHz, RS232 Module RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V