参数资料
| 型号： | MIC2150YML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 15/27页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 24MLF |
| 标准包装： | 1 |
| PWM 型： | 电流/电压模式 |
| 输出数： | 2 |
| 频率 - 最大： | 550kHz |
| 占空比： | 80% |
| 电源电压： | 4.5 V ~ 14.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 24-VFQFN 裸露焊盘，24-MLF? |
| 包装： | 标准包装 |
| 其它名称： | 576-3746-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
Micrel, Inc.
MIC2150
Application Information
VOUT PK ? PK ≈ I RIPPLE × ESR +
I RIPPLE × t ON
2 × C OUT
Passive Component Selection Guide
Inductor Selection
The inductor value is responsible for the ripple current
which causes some proportion of the resistive losses in
the power components. These losses are proportional to
I RIPPLE2 . Minimizing inductor ripple current can therefore
reduce the RMS current flowing in the power
components and generally improve efficiency; this is
achieved by choosing a larger value inductor. Having
said this, the actual value of inductance is realistically
defined by space limitations, RMS rating (I RMS ) and
saturation current (I SAT ) of available inductors. If one
looks at the newer flat wire inductors for example, these
typically have higher I SAT ratings than the I RMS for lower
values. Also, as inductance value increases, these
figures tend to get closer in value. This mirrors what
happens in the converter with I SAT analogous to the
maximum peak switch current and I RMS analogous to
output current. As inductance increases, so I SWITCH(PK)
tends towards I OUT . This is a characteristic that makes
these types of inductor optimal for use with high power
buck converters such as MIC2150.
To determine the I SAT and I RMS rating of the inductor, we
should start with a nominal value of ripple current. This
should typically be no more than I OUT(MAX) /2 to minimize
MOSFET losses due to ripple current mentioned earlier.
Therefore:
If therefore, the need is for low output voltage noise
(e.g., in low output voltage converters), V OUT ripple can
be directly reduced by increasing inductor value, output
capacitor value or reducing ESR.
For tantalum capacitors, ESR is typically >40m Ω which
usually makes loop stabilization easier by utilizing a
pole-zero (type II) compensator.
Due to many advantages of multi-layer ceramic
capacitors, among them, cost, size, ripple rating and
ESR, it can be useful to choose these in many cases.
However, one disadvantage is the CV product. This is
lower than tantalum. A mixture of one tantalum and one
ceramic can be a good compromise which can still utilize
the simple type II compensator.
With ceramic output capacitors only, a double-pole,
double-zero (type III) compensator is required to ensure
system stability. Loop compensation is described in
more detail later in the data sheet.
Ensure the RMS ripple current rating of the capacitor is
above I RIPPLE ×0.6 to improve reliability.
Input Capacitor Selection
C IN ripple rating for a single phase converter is typically
I OUT /2 under worst case duty cycle conditions of 50%.
This increases ~10% for a ripple current of I OUT /2.
When both cycles are switching 180° out of phase, the
ripple can reduce at DC <50% to:
L MIN ~ 2 ×
V OUT
I OUT × F S
× ( 1 ?
V OUT
V IN × Efficiency
)
I RMSCIN = I 1 2 × D 1 × ( 1 ? D 1 ) + I 2 2 × D 2 × ( 1 ? D 2 ) ? 2 × I 1 × I 2 × D 1 × D 2
I RIPPLE ~
× OUT
I LRMS > 1.04×I OUT(MAX)
I LSAT > 1.25×I OUT(MAX)
Any value chosen above L MIN will ensure these ratings
are not exceeded.
In considering the actual value to choose, one needs to
look at the effect of ripple on the other components in
the circuit. The chosen inductor value will have a ripple
current of:
(1 ? D ) V
F S L
This value should ideally be kept to a minimum, within
the cost and size constraints of the design, to reduce
unnecessary heat dissipation.
Output Capacitor Selection
The output capacitor (C OUT ) will have the full inductor
ripple current I RIPPLERMS flowing through it. This creates
the output switching noise which consists of two main
components:
It is however, also advisable to closely decouple the
Power MOSFETs with 2×10μF ceramic capacitors to
reduce ringing and prevent noise related issues from
causing problems in the layout of the regulator. The
ripple rating of C IN may therefore, be satisfied by these
decoupling capacitors; allowing the use of perhaps one
more ceramic or tantalum input capacitor at the input
voltage node to decouple input noise and localize high
di/dt signals to the regulator input.
Power MOSFET Selection
The MIC2150 drives N-Channel MOSFETs in both the
upper and lower positions. This is because the switching
speed for a given R DSON in the N-Channel device is
superior to the P-Channel device.
There are different criteria for choosing the upper and
lower MOSFETs and these criteria are more marked at
lower duty cycles such as 12V to 1.8V conversion. In
such an application, the upper MOSFET is required to
switch as quickly as possible to minimize transition
August 2009
15
M9999-082809-A
(408) 944-0800
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2156YML TR | IC REG CTRLR BUCK PWM VM 32MLF |
| MIC2159YMME | IC REG CTRLR BUCK PWM VM 10-MSOP |
| MIC2164YMM | IC REG CTRLR BUCK PWM 10-MSOP |
| MIC2165YMME TR | IC REG CTRLR BUCK PWM 10TSOP |
| MIC2166YMME TR | IC REG CTRLR PWM HYBRID 10TSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2151 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:2-Phase Dual Output PWM Synchronous Buck Control IC |
| MIC2151YML | 制造商:Micrel 功能描述:Micrel MIC2151YML |
| MIC2155 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:2-Phase, Single Output, PWM Synchronous Buck Control IC |
| MIC2155_0911 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Two-Phase, Single-Output, PWM Synchronous Buck Control IC |
| MIC2155YML | 制造商:Micrel 功能描述:The Micrel MIC2155YML is a 50A Synchronous Buck Regulator. |
发布紧急采购，3分钟左右您将得到回复。