- 您现在的位置：买卖IC网 > PDF目录15371 > MIC2164-2YMM TR (Micrel Inc)IC REG CTRLR BUCK PWM 10-MSOP PDF资料下载
参数资料
| 型号： | MIC2164-2YMM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 19/39页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 10-MSOP |
| 产品培训模块： | MIC2124 Synchronous Current Mode DC-DC Buck Controller |
| 标准包装： | 2,500 |
| 系列： | Hyper Speed Control™ |
| PWM 型： | 混合物 |
| 输出数： | 1 |
| 频率 - 最大： | 750kHz |
| 占空比： | 74% |
| 电源电压： | 3 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
Micrel, Inc.
External Schottky Diode (Optional)
An external freewheeling diode, which is generally not
necessary, can be used to keep the inductor current flow
continuous while both MOSFETs are turned off. This
dead time prevents current from flowing unimpeded
through both MOSFETs and is typically 30ns. The diode
conducts twice during each switching cycle. Although the
average current through this diode is small, the diode
must be able to handle the peak current.
MIC2164/-2/-3/C
Ripple Injection
The minimum FB voltage ripple requested by the
MIC2164/-2/-3 g m amplifier and error comparator is
20mV (100mV maximum). However, the output voltage
ripple is generally designed as 1% to 2% of the output
voltage. For a low output voltage, such as 1V output, the
output voltage ripple is only 10mV to 20mV, and the FB
voltage ripple is less than 20mV. If the FB voltage ripple
is so small that the g m amplifier and error comparator
could not sense it, then the MIC2164/-2/-3 will lose
I D(avg) = I OUT ? 2 ? 30ns ? f SW
The reverse voltage requirement of the diode is:
V DIODE(rrm) = V HSD
The power dissipated by the Schottky diode is:
P DIODE = I D(avg) × V F
(25)
(26)
control and the output voltage will not be regulated. In
order to have some amount of FB voltage ripple, the
ripple injection method is applied for low output voltage
ripple applications.
The applications are divided into three situations
according to the amount of the FB voltage ripple:
1) Enough ripple at the FB voltage due to the large ESR
of the output capacitors.
As shown in Figure 5a, the converter is stable without
any adding in this situation. The FB voltage ripple is:
where, V F = forward voltage at the peak diode current.
The external Schottky diode is not necessary for the
Δ V FB(pp) =
R2
R1 + R2
? ESR C OUT ? Δ I L (pp)
(27)
circuit operation since the low-side MOSFET contains a
parasitic body diode. The external diode will improve
efficiency and decrease the high frequency noise. If the
MOSFET body diode is then used, it must be rated to
handle the peak and average current. The body diode
has a relatively slow reverse recovery time and a
relatively high forward voltage drop. The power lost in
the diode is proportional to the forward voltage drop of
the diode. As the high-side MOSFET starts to turn on,
the body diode becomes a short circuit for the reverse
recovery period, dissipating additional power. The diode
where Δ I L(pp) is the peak-to-peak value of the inductor
current ripple.
2) Inadequate ripple at the FB voltage due to the small
ESR of the output capacitors.
The output voltage ripple is fed into the FB pin through a
feedforward capacitor Cff in this situation, as shown in
Figure 5b. The typical Cff value is between 1nF to
100nF. With the feedforward capacitor, the FB voltage
ripple is very close to the output voltage ripple:
recovery and the circuit inductance will cause ringing
during the high-side MOSFET turn-on.
An external Schottky diode conducts at a lower forward
Δ V FB(pp) ≈ ESR ? Δ I L (pp)
(28)
voltage preventing the body diode in the MOSFET from
turning on. The lower forward voltage drop dissipates
less power than the body diode. The lack of a reverse
recovery mechanism in a Schottky diode causes less
ringing and less power loss. Depending upon the circuit
components and operating conditions, an external
Schottky diode will give a ? to 1% improvement in
efficiency.
3) Invisible ripple at the FB voltage is due to the very low
ESR of the output capacitors.
September 2010
19
M9999-091310-D
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B1K-EV-F4 | CONVERTER MOD DC/DC 40V 150W |
| ACM10DRKN | CONN EDGECARD 20POS DIP .156 SLD |
| 2727-13J | INDUCTOR TOROID 100UH SHIELD RAD |
| ACC07DRES-S734 | CONN EDGECARD 14POS .100 EYELET |
| 2727-10J | INDUCTOR TOROID 56UH SHIELD RADL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2164-3YMM | 功能描述:DC/DC 开关控制器 1MHz PWM Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2164-3YMM TR | 功能描述:DC/DC 开关控制器 1MHz PWM Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2164CYMM | 功能描述:DC/DC 开关控制器 Constant Freq Sync DC-DC Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2164CYMM TR | 功能描述:DC/DC 开关控制器 Constant Freq Sync DC-DC Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2164YMM | 功能描述:DC/DC 开关控制器 300kHz PWM Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。