- 您现在的位置：买卖IC网 > PDF目录15371 > MIC2164-2YMM TR (Micrel Inc)IC REG CTRLR BUCK PWM 10-MSOP PDF资料下载
参数资料
| 型号： | MIC2164-2YMM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 22/39页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 10-MSOP |
| 产品培训模块： | MIC2124 Synchronous Current Mode DC-DC Buck Controller |
| 标准包装： | 2,500 |
| 系列： | Hyper Speed Control™ |
| PWM 型： | 混合物 |
| 输出数： | 1 |
| 频率 - 最大： | 750kHz |
| 占空比： | 74% |
| 电源电压： | 3 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
Micrel, Inc.
PCB Layout Guideline
Warning!!! To minimize EMI and output noise, follow
these layout recommendations.
MIC2164/-2/-3/C
capacitor is very critical. Connections must be made
with wide trace.
Inductor
PCB Layout is critical to achieve reliable, stable and
efficient performance. A ground plane is required to
control EMI and minimize the inductance in power,
signal and return paths.
The following guidelines should be followed to insure
proper operation of the MIC2164/-2/-3 converter.
IC
?
?
?
?
Keep the inductor connection to the switch node
(LX) short.
Do not route any digital lines underneath or close to
the inductor.
Keep the switch node (LX) away from the feedback
(FB) pin.
The LX pin should be connected directly to the drain
?
?
Place the IC and MOSFETs close to the point of
load (POL).
Use fat traces to route the input and output power
lines.
?
of the low-side MOSFET to accurate sense the
voltage across the low-side MOSFET.
To minimize noise, place a ground plane underneath
the inductor.
?
Signal and power grounds should be kept separate
and connected at only one location.
Output Capacitor
? Use a wide trace to connect the output capacitor
Input Capacitor
? Place the HSD input capacitor next.
? Place the HSD input capacitors on the same side of
the board and as close to the MOSFETs as
possible.
? Keep both the HSD and PGND connections short.
? Place several vias to the ground plane close to the
HSD input capacitor ground terminal.
?
?
ground terminal to the input capacitor ground
terminal.
Phase margin will change as the output capacitor
value and ESR changes. Contact the factory if the
output capacitor is different from what is shown in
the BOM.
The feedback trace should be separate from the
power trace and connected as close as possible to
the output capacitor. Sensing a long high current
?
?
?
?
?
?
Use either X7R or X5R dielectric input capacitors.
Do not use Y5V or Z5U type capacitors.
Do not replace the ceramic input capacitor with any
other type of capacitor. Any type of capacitor can be
placed in parallel with the input capacitor.
If a Tantalum input capacitor is placed in parallel
with the input capacitor, it must be recommended for
switching regulator applications and the operating
voltage must be derated by 50%.
In “Hot-Plug” applications, a Tantalum or Electrolytic
bypass capacitor must be used to limit the over-
voltage spike seen on the input supply with power is
suddenly applied.
An additional Tantalum or Electrolytic bypass input
capacitor of 22uF or higher is required at the input
power connection.
The 1μF and 0.1μF capacitors, which connect to the
V IN terminal, must be located right at the IC. The V IN
terminal is very noise sensitive and placement of the
load trace can degrade the DC load regulation.
Schottky Diode (Optional)
? Place the Schottky diode on the same side of the
board as the MOSFETs and HSD input capacitor.
? The connection from the Schottky diode’s Anode to
the input capacitors ground terminal must be as
short as possible.
? The diode’s cathode connection to the switch node
(LX) must be keep as short as possible.
RC Snubber
? Place the RC snubber on the same side of the board
and as close to the MOSFETs as possible.
September 2010
22
M9999-091310-D
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B1K-EV-F4 | CONVERTER MOD DC/DC 40V 150W |
| ACM10DRKN | CONN EDGECARD 20POS DIP .156 SLD |
| 2727-13J | INDUCTOR TOROID 100UH SHIELD RAD |
| ACC07DRES-S734 | CONN EDGECARD 14POS .100 EYELET |
| 2727-10J | INDUCTOR TOROID 56UH SHIELD RADL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2164-3YMM | 功能描述:DC/DC 开关控制器 1MHz PWM Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2164-3YMM TR | 功能描述:DC/DC 开关控制器 1MHz PWM Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2164CYMM | 功能描述:DC/DC 开关控制器 Constant Freq Sync DC-DC Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2164CYMM TR | 功能描述:DC/DC 开关控制器 Constant Freq Sync DC-DC Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2164YMM | 功能描述:DC/DC 开关控制器 300kHz PWM Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。