- 您现在的位置：买卖IC网 > PDF目录15505 > MIC2164-3YMM (Micrel Inc)IC REG CTRLR BUCK PWM 10-MSOP PDF资料下载
参数资料
| 型号： | MIC2164-3YMM |
| 厂商： | Micrel Inc |
| 文件页数： | 13/39页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 10-MSOP |
| 产品培训模块： | MIC2124 Synchronous Current Mode DC-DC Buck Controller |
| 标准包装： | 100 |
| 系列： | Hyper Speed Control™ |
| PWM 型： | 混合物 |
| 输出数： | 1 |
| 频率 - 最大： | 1.25MHz |
| 占空比： | 66% |
| 电源电压： | 3 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1092 (CN2011-ZH PDF) |
| 其它名称： | 576-3544-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
Micrel, Inc.
Functional Description
The MIC2164/-2/-3 is an adaptive on-time synchronous
MIC2164/-2/-3/C
The maximum duty cycle is obtained from the 363ns
T OFF(min) :
buck controller family built for low cost and high
performance. They are designed for a wide input voltage
range from 3V to 28V and for high output power buck
converters. An estimated-ON-time method is applied in
Dmax =
T S ? T OFF(min)
T S
= 1 ?
363ns
T S
MIC2164/-2/-3 to obtain a constant switching frequency
T ON(estimat ed) =
V OUT
and to simplify the control compensation. The over-
current protection is implemented without the use of an
external sense resistor. It includes an internal soft-start
function which reduces the power supply input surge
current at start-up by controlling the output voltage rise
time.
Theory of Operation
The MIC2164/-2/-3 is a adaptive on-time buck controller
family. Figure 1 illustrates the block diagram for the
control loop. The output voltage variation will be sensed
by the MIC2164/-2/-3 feedback pin FB via the voltage
divider R1 and R2, and compared to a 0.8V reference
voltage V REF at the error comparator through a low gain
transconductance (g m ) amplifier, the amplifier improves
the MIC2164/-2/-3 converter output voltage regulation. If
the FB voltage decreases and the output of the g m
amplifier is below 0.8V, The error comparator will trigger
the control logic and generate an ON-time period, in
which DH pin is logic high and DL pin is logic low. The
ON-time period length is predetermined by the “FIXED
T ON ESTIMATION” circuitry:
(1)
V HSD × f sw
where V OUT is the output voltage, V HSD is the power
stage input voltage, and f SW is the switching frequency
(300kHz for MIC2164, 600kHz for MIC2164-2, and
1MHz for MIC2164-3).
After ON-time period, the MIC2164/-2/-3 goes into the
OFF-time period, in which DH pin is logic low and DL pin
is logic high. The OFF-time period length is depending
on the FB voltage in most cases. When the FB voltage
decreases and the output of the g m amplifier is below
0.8V, then the ON-time period is trigger and the OFF-
time period ends. If the OFF-time period decided by the
FB voltage is less than the minimum OFF time T OFF(min) ,
which is about 363ns typical, then the MIC2164/-2/-3
control logic will apply the T OFF(min) instead. T OFF(min) is
required by the BST charging.
where Ts = 1/f SW .
It is not recommended to use MIC2164/-2/-3 with a OFF
time close to T OFF(min) at the steady state. Also, as V OUT
increases, the internal ripple injection will increase and
reduce the line regulation performance. Therefore, the
maximum output voltage of the MIC2164/-2/-3 should be
limited to 5.5V. If a higher output voltage is required, use
the MIC2176 instead. Please refer to “Setting Output
Voltage” subsection in “Application Information” for more
details.
The estimated-ON-time method results in a constant
switching frequency in MIC2164/-2/-3. The actual ON
time is varied with the different rising and falling time of
the external MOSFETs. Therefore, the type of the
external MOSFETs, the output load current, and the
control circuitry power supply V IN will modify the actual
ON time and the switching frequency. Also, the minimum
T ON results in a lower switching frequency in the high
V HSD and low V OUT applications, such as 24V to 1.0V
MIC2164-3 application. The minimum T ON measured on
the MIC2164 evaluation board is about 138ns. During
the load transient, the switching frequency is changed
due to the varying OFF time.
To illustrate the control loop, the steady-state scenario
and the load transient scenario are analyzed. For easy
analysis, the gain of the g m amplifier is assumed to be 1.
With this assumption, the inverting input of the error
comparator is the same as the FB voltage. Figure 2
shows the MIC2164/-2/-3 control loop timing during the
steady-state. During the steady-state, the g m amplifier
senses the FB voltage ripple, which is proportional to the
output voltage ripple and the inductor current ripple, to
trigger the ON-time period. The ON time is
predetermined by the estimation. The ending of OFF
time is controlled by the FB voltage. At the valley of the
FB voltage ripple, which is below than V REF , OFF period
ends and the next ON-time period is triggered through
the control logic circuitry.
September 2010
13
M9999-091310-D
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2164-2YMM | IC REG CTRLR BUCK PWM 10-MSOP |
| SP6125EK1-L | IC REG CTRLR BUCK PWM VM 6TSOT |
| MIC2164CYMM | IC REG CTRLR BUCK PWM 10-MSOP |
| SP6127EK1-L | IC REG CTRLR BUCK PWM VM 6TSOT |
| MIC2124YMM | IC REG CTRLR BUCK PWM CM 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2164-3YMM TR | 功能描述:DC/DC 开关控制器 1MHz PWM Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2164CYMM | 功能描述:DC/DC 开关控制器 Constant Freq Sync DC-DC Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2164CYMM TR | 功能描述:DC/DC 开关控制器 Constant Freq Sync DC-DC Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2164YMM | 功能描述:DC/DC 开关控制器 300kHz PWM Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2164YMM TR | 功能描述:DC/DC 开关控制器 300kHz PWM Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。