- 您现在的位置：买卖IC网 > PDF目录15332 > MIC2182-5.0YM TR (Micrel Inc)IC REG CTRLR BUCK PWM CM 16-SOIC PDF资料下载
参数资料
| 型号： | MIC2182-5.0YM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-SOIC |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 330kHz |
| 占空比： | 86% |
| 电源电压： | 4.5 V ~ 32 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2182-5.0YMTR MIC2182-5.0YMTR-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
MIC2182
Applications Information
The following applications information includes component
selection and design guidelines. See Figure 14 and Tables 1
through 5 for predesigned circuits.
Inductor Selection
Values for inductance, peak, and RMS currents are required
to select the output inductor. The input and output voltages
and the inductance value determine the peak to peak inductor
ripple current. Generally, higher inductance values are used
with higher input voltages. Larger peak to peak ripple currents
will increase the power dissipation in the inductor and
MOSFETs. Larger output ripple currents will also require
more output capacitance to smooth out the larger ripple
current. Smaller peak to peak ripple currents require a larger
inductance value and therefore a larger and more expensive
inductor. A good compromise between size, loss and cost is
to set the inductor ripple current to be equal to 20% of the
maximum output current.
The inductance value is calculated by the equation below.
Micrel
output currents, the core losses can be a significant contribu-
tor. Core loss information is usually available from the mag-
netics vendor.
Copper loss in the inductor is calculated by the equation
below:
P inductor Cu = I inductor (rms) 2 × R winding
The resistance of the copper wire, R winding , increases with
temperature. The value of the winding resistance used should
be at the operating temperature.
R winding(hot) = R winding(20 ° C) × ( 1 + 0.0042 × (T hot ? T 20 ° C ) )
where:
T HOT = temperature of the wire
under operating load
T 20 ° C = ambient temperature
R winding(20 ° C) is room temperature winding resistance
(usually specified by the manufacturer)
L =
V OUT × (V IN(max) ? V OUT )
V IN(max) × f S × 0.2 × I OUT(max)
Current-Sense Resistor Selection
Low inductance power resistors, such as metal film resistors
should be used. Most resistor manufacturers make low
V OUT × (V IN(max) ? V OUT )
V IN(max) × f S × L
R SENSE =
where:
f S = switching frequency
0.2 = ratio of ac ripple current to dc output current
V IN(max) = maximum input voltage
The peak-to-peak inductor current (ac ripple current) is:
I PP =
The peak inductor current is equal to the average output
current plus one half of the peak to peak inductor ripple
inductance resistors with low temperature coefficients, de-
signed specifically for current-sense applications. Both resis-
tance and power dissipation must be calculated before the
resistor is selected. The value of R SENSE is chosen based on
the maximum output current and the maximum threshold
level. The power dissipated is based on the maximum peak
output current at the minimum overcurrent threshold limit.
75mV
I OUT(max)
The maximum overcurrent threshold is:
current.
I PK = I OUT(max) + 0.5 × I PP
I overcurrent(max) =
135mV
R CS
The RMS inductor current is used to calculate the I 2 · R losses
The maximum power dissipated in the sense resistor is:
in the inductor.
I inductor (rms) = I OUT(max) × 1 +
1 ? I PP ?
? ?
3 ? I OUT(max) ?
2
P D(R SENSE ) = I overcurrent(max)2 × R CS
MOSFET Selection
External N-channel logic-level power MOSFETs must be
used for the high- and low-side switches. The MOSFET gate-
Maximizing efficiency requires the proper selection of core
material and minimizing the winding resistance. The high
frequency operation of the MIC2182 requires the use of ferrite
materials for all but the most cost sensitive applications.
Lower cost iron powder cores may be used but the increase
in core loss will reduce the efficiency of the power supply. This
is especially noticeable at low output power. The winding
resistance decreases efficiency at the higher output current
levels. The winding resistance must be minimized although
this usually comes at the expense of a larger inductor.
The power dissipated in the inductor is equal to the sum of the
core and copper losses. At higher output loads, the core
losses are usually insignificant and can be ignored. At lower
to-source drive voltage of the MIC2182 is regulated by an
internal 5V V DD regulator. Logic-level MOSFETs, whose
operation is specified at V GS = 4.5V must be used.
It is important to note the on-resistance of a MOSFET
increases with increasing temperature. A 75 ° C rise in junc-
tion temperature will increase the channel resistance of the
MOSFET by 50% to 75% of the resistance specified at 25 ° C.
This change in resistance must be accounted for when
calculating MOSFET power dissipation.
Total gate charge is the charge required to turn the MOSFET
on and off under specified operating conditions (V DS and
V GS ). The gate charge is supplied by the MIC2182 gate drive
circuit. At 300kHz switching frequency and above, the gate
M9999-042204
16
April 22, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| ADM8691ARU-REEL | IC SUPERVSR MPU 4.65V ADJ16TSSOP |
| UPM1A182MHD6 | CAP ALUM 1800UF 10V 20% RADIAL |
| RSM10DTAS | CONN EDGECARD 20POS R/A .156 SLD |
| IDCS2512ER100M | INDUCTOR POWER 10UH 1.0A SMD |
| LTC1772IS6#TRPBF | IC REG CTRLR BUCK PWM CM SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2182BM | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2182BM TR | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2182BSM | 功能描述:DC/DC 开关控制器 High EfficiencySynchronous Buck Controller SSOP Pkg RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2182BSM TR | 功能描述:DC/DC 开关控制器 High EfficiencySynchronous Buck Controller SSOP Pkg RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2182BSMTR | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。