- 您现在的位置：买卖IC网 > PDF目录15332 > MIC2182-5.0YM TR (Micrel Inc)IC REG CTRLR BUCK PWM CM 16-SOIC PDF资料下载
参数资料
| 型号： | MIC2182-5.0YM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 20/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-SOIC |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 330kHz |
| 占空比： | 86% |
| 电源电压： | 4.5 V ~ 32 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2182-5.0YMTR MIC2182-5.0YMTR-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页
MIC2182
pins and routed with a wide trace. The capacitor should be a
good quality tantalum. An additional 1 μ F ceramic capacitor
may be necessary when driving large MOSFETs with high
gate capacitance. Incorrect placement of the V DD decoupling
capacitor will cause jitter or oscillations in the switching
waveform and large variations in the overcurrent limit.
A 0.1 μ F ceramic capacitor is required to decouple the VIN.
The capacitor should be placed near the IC and connected
directly to between pin 10 (Vcc) and pin 12 (PGND).
PCB Layout and Checklist
PCB layout is critical to achieve reliable, stable and efficient
performance. A ground plane is required to control EMI and
minimize the inductance in power, signal and return paths.
The following guidelines should be followed to insure proper
operation of the circuit.
? Signal and power grounds should be kept
separate and connected at only one location.
Large currents or high di/dt signals that occur
when the MOSFETs turn on and off must be
kept away from the small signal connections.
? The connection between the current-sense
resistor and the MIC2182 current-sense inputs
(pin 8 and 9) should have separate traces,
routed from the terminals directly to the IC pins.
The traces should be routed as closely as
possible to each other and their length should be
minimized. Avoid running the traces under the
inductor and other switching components. A 1nF
to 0.1 μ F capacitor placed between pins 8 and 9
will help attenuate switching noise on the current
sense traces. This capacitor should be placed
close to pins 8 and 9.
Micrel
? When the high-side MOSFET is switched on, the
critical flow of current is from the input capacitor
through the MOSFET, inductor, sense resistor,
output capacitor, and back to the input capacitor.
These paths must be made with short, wide
pieces of trace. It is good practice to locate the
ground terminals of the input and output capaci-
tors close to each.
? When the low-side MOSFET is switched on,
current flows through the inductor, sense
resistor, output capacitor, and MOSFET. The
source of the low-side MOSFET should be
located close to the output capacitor.
? The freewheeling diode, D1 in Figure 2, con-
ducts current during the dead time, when both
MOSFETs are off. The anode of the diode
should be located close to the output capacitor
ground terminal and the cathode should be
located close to the input side of the inductor.
? The 4.7 μ F capacitor, which connects to the VDD
terminal (pin 11) must be located right at the IC.
The VDD terminal is very noise sensitive and
placement of this capacitor is very critical.
Connections must be made with wide trace. The
capacitor may be located on the bottom layer of
the board and connected to the IC with multiple
vias.
? The V IN bypass capacitor should be located
close to the IC and connected between pins 10
and 12. Connections should be made with a
ground and power plane or with short, wide
trace.
M9999-042204
20
April 22, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| ADM8691ARU-REEL | IC SUPERVSR MPU 4.65V ADJ16TSSOP |
| UPM1A182MHD6 | CAP ALUM 1800UF 10V 20% RADIAL |
| RSM10DTAS | CONN EDGECARD 20POS R/A .156 SLD |
| IDCS2512ER100M | INDUCTOR POWER 10UH 1.0A SMD |
| LTC1772IS6#TRPBF | IC REG CTRLR BUCK PWM CM SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2182BM | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2182BM TR | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2182BSM | 功能描述:DC/DC 开关控制器 High EfficiencySynchronous Buck Controller SSOP Pkg RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2182BSM TR | 功能描述:DC/DC 开关控制器 High EfficiencySynchronous Buck Controller SSOP Pkg RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2182BSMTR | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。