- 您现在的位置：买卖IC网 > PDF目录15114 > MIC2185BQS (Micrel Inc)IC REG CTRLR BST PWM CM 16-QSOP PDF资料下载
参数资料
| 型号： | MIC2185BQS |
| 厂商： | Micrel Inc |
| 文件页数： | 13/15页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM CM 16-QSOP |
| 标准包装： | 98 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 440kHz |
| 占空比： | 95% |
| 电源电压： | 2.9 V ~ 14 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
R2
V O = V REF × ? 1 +
? R1 ?
?
R2 ?
MIC2185
Soft Start
Soft Start reduces the power supply input surge current at
start up by limiting the output voltage rise time. Input surge
current occurs when the boost converter charges up the output
capacitance. Slowing the output rise time lowers the input
surge current. Soft Start may also be used for power supply
sequencing. The soft start cannot control the initial surge of
current in a boost converter when V IN is applied. This surge
current is caused by the output capacitance charging up to
the input voltage. The current ?ows from the input through
the inductor and output diode to the output capacitors.
The soft start voltage is applied directly to the PWM compara-
tor. A 5μA internal current source is used to charge up the
soft start capacitor. Either of 2 UVLO conditions will pull the
soft start capacitor low.
? When the V DD voltage drops below its UVLO
threshold
? When the Enable pin drops below the UVLO
threshold
The part switches at a low duty cycle when the soft start pin
voltage zero. As the soft start voltage rises from 0V to 0.7V,
the duty cycle increases from the minimum duty cycle to
the operating duty cycle. The oscillator runs at the foldback
frequency until the feedback voltage rises above 0.3V. In
a boost converter the output voltage is equal to the input
voltage before the MIC2185 starts switching. If the ratio of
Vout/Vin is low, the voltage on the feedback pin will already
be greater than 0.3V and the converter begin switching at
the selected operating frequency.
The risetime of the output is dependent on the soft start
capacitor, output capacitance, input and output voltage and
load current. The scope photo in Figure10 shows the output
voltage and the soft start pin voltage at startup. The output
voltage is initially at the input voltage less a diode drop. After
the converter is enabled the output slowly rises due to the
minimum duty cycle of the controller. As the soft start voltage
increases, the output voltage rises in a controlled fashion until
the output voltage reaches the regulated value.
Soft StartWaveform
VOUT
2V/div
VSS
1V/div
0V
TIME (2ms/div)
Figure 10 Soft Start
Micrel, Inc.
Voltage Setting Components
The MIC2185 requires two resistors to set the output voltage
as shown in Figure 11.
MIC2185
Voltage R1
Amplifier
Pin
6
V REF
1.245V
Figure 11
The output voltage is determined by the equation below.
?
where:
V REF for the MIC2185 is nominally 1.245V.
Lower values of resistance are preferred to prevent noise
from apprearing on the V FB pin. A typically recommended
value for R1 is 10kΩ.
Decoupling Capacitor Selection
A 1μF decoupling capacitor is used to stabilize the internal
regulator and minimize noise on the VDD pin. Placement
of this capacitor is critical to the proper operation of the
MIC2185. It must be next to the VDD and signal ground
pins. The capacitor should be a good quality ceramic. Incor-
rect placement of the VDD decoupling capacitor will cause
jitter and/or oscillations in the switching waveform as well as
variations in the overcurrent limit.
A minimum 0.1μF ceramic capacitor is required to decouple
the V IN pin. The capacitor should be placed near the IC and
connected directly between pin 10 (VDD) and pin 5 (SGND).
A 0.1μF capacitor is required to decouple VREF. It should
be located near the VREF pin.
Ef?ciency calculation and considerations
Ef?ciency is the ratio of output power to input power. The
difference is dissipated as heat in the boost converter. The
signi?cant contributors at light output loads are:
? The V IN A pin supply current.
? The V IN P pin supply current which includes the
current required to switch the external MOSFETs
? Core losses in the inductor
To maximize ef?ciency at light loads:
? Use a low gate charge MOSFET or use the
smallest MOSFET, which is still adequate for the
maximum output current.
? Allow the MIC2185 to run in skip mode at lower
currents. If running in PWM mode, set the fre-
quency to 200kHz.
October 2005
13
MIC2185
相关PDF资料 |
PDF描述 |
|---|---|
| GCM44DRPH | CONN EDGECARD 88POS DIP .156 SLD |
| SLPX393M010H3P3 | CAP ALUM 39000UF 10V 20% SNAP |
| VE-21Z-EX-B1 | CONVERTER MOD DC/DC 2V 30W |
| UPM1J102MHD | CAP ALUM 1000UF 63V 20% RADIAL |
| RCC26DRYS-S93 | CONN EDGECARD 52POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2185BQS TR | 功能描述:IC REG CTRLR BST PWM CM 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2185YM | 功能描述:DC/DC 开关控制器 SO-16 Low Vin Synchronous Buck PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2185YM TR | 功能描述:DC/DC 开关控制器 SO-16 Low Vin Synchronous Buck PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2185YQS | 功能描述:DC/DC 开关控制器 SO-16 Low Vin Synchronous Buck PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2185YQS TR | 功能描述:DC/DC 开关控制器 SO-16 Low Vin Synchronous Buck PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。