- 您现在的位置：买卖IC网 > PDF目录15332 > MIC2186YM TR (Micrel Inc)IC REG CTRLR BST FLYBK CM 16SOIC PDF资料下载
参数资料
| 型号： | MIC2186YM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 9/15页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST FLYBK CM 16SOIC |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 440kHz |
| 占空比： | 85% |
| 电源电压： | 2.9 V ~ 14 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2186YMTR MIC2186YMTR-ND |
MIC2186
SKIP Mode Operation
Low Current
Micrel, Inc.
0
This control method is used to improve efficiency at low
output loads. A block diagram of the MIC2186 SKIP mode is
shown in Figure 2. The power drawn by the MIC2186 control
IC is (I VIN A · V IN A )+ (I VIN P · V IN P). The power dissipated by
the IC can be a significant portion of the total output power
during periods of low output current, which lowers the effi-
ciency of the power supply. In SKIP mode the MIC2186
lowers the IC supply current by turning off portions of the
control and drive circuitry when the IC is not switching. The
disadvantage of this method is greater output ripple and
variable switching frequency. The soft start, HiDC and Sync
80
70
60
50
40
30
20
10
0
Efficiency
PWM Mode
SKIP Mode
0.05 0.1 0.15 0.2 0.25
INPUT CURRENT (A)
pins have no effect when operating in SKIP mode.
In SKIP mode, switching starts when the feedback voltage
drops below the lower threshold level of the hysteresis
comparator. The OutN pin goes high, turning on the N-
channel MOSFET, Q1. Current ramps up in the inductor until
either the current limit comparator or the hysteretic voltage
comparator turns off Q1’s gate drive. If the feedback voltage
exceeds the upper hysteretic threshold, Q1’s gate drive is
terminated. However, if the voltage at the CSH pin exceeds
the SKIP mode current limit threshold, it terminates the gate
drive for that switching cycle. The gate drive remains off for
a constant period at the end of each switching cycle. This off
time period is typically 1 μ s when the F/2 pin is low and 2 μ s
when the F/2 pin is high. Figure 3 shows some typical SKIP
Figure 4.
The maximum peak inductor current depends on the skip
current limit threshold and the value of the current sense
resistor, Rsense. For a typical 50mV current limit threshold in
SKIP Mode, the peak inductor current is:
50mV
I INDUCTOR_pk =
R SENSE
The maximum output current is SKIP mode depends on the
input conditions, output conditions and circuit component
values. Assuming a discontinuous mode where the inductor
current starts from zero at each cycle, the maximum output
current is calculated below:
mode switching waveforms.
I_inductor
V IN
Voltage
I O(max) =
where:
2.5 × 10 ? 3 × L × fs
2 × R SENSE2 × ( V O ? η × V IN
)
Divider
Gate Driver
I_inductor
Iomax is the maximum output current
Vo is the output voltage
I_inductor
V REF
Vin is the input voltage
I_inductor
L is the value of the boost inductor
V COMP
Gate Drive at OutN
T ON
T PER
Figure 3. SKIP Mode Waveform
The SKIP mode current threshold limits the peak inductor
current per cycle. Depending on the input, output and circuit
parameters, many switching cycles can occur before the
feedback voltage exceeds the upper hysteretic threshold.
Once the voltage on the feedback pin exceeds the upper
hysteretic threshold the gate drive is disabled. The output
load discharges the output capacitance causing Vout to
decrease until the feedback voltage drops below the lower
threshold voltage limit. The switching converter then turns the
gate drive back on. While the gate drive is disabled, the
MIC2186 draws less IC supply current then while it is switch-
ing, thereby improving efficiency at low output loads. Figure
4 shows the efficiency improvement at low output loads when
SKIP mode is selected.
fs is the switching frequency
η is the efficiency of the boost converter
Rsense it the value of the current sense resistor
2.5·10 -3 is a constant based on the SKIP mode
current threshold (50mV) 2
PWM Operation
Figure 5 shows typical waveforms for PWM mode of opera-
tion. The gate drive signal turns on the external MOSFET
which allows the inductor current to ramp up. When the
MOSFET turns off, the inductor forces the MOSFET drain
voltage to rise until the boost diode turns on and the voltage
is clamped at approximately the output voltage.
April 2005
9
M9999-042205
相关PDF资料 |
PDF描述 |
|---|---|
| ASM10DRYH-S13 | CONN EDGECARD 20POS .156 EXTEND |
| UPM1E152MHD | CAP ALUM 1500UF 25V 20% RADIAL |
| MIC2185YM TR | IC REG CTRLR BST PWM CM 16-SOIC |
| IDCS2512ER152M | INDUCTOR POWER 1500UH 0.12A SMD |
| MIC2184YM TR | IC REG CTRLR BUCK PWM CM 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2186YQS | 功能描述:DC/DC 开关控制器 SO-16 Low Vin Synchronous Buck PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2186YQS TR | 功能描述:DC/DC 开关控制器 SO-16 Low Vin Synchronous Buck PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2193 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:400KHZ SO 8 SYNCHRONOUS BUCK CONTROL IC |
| MIC2193BM | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2193BM TR | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。