参数资料
| 型号： | MIC22602YML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 18/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 6A 24MLF |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 0.7V |
| 输入电压： | 2.6 V ~ 5.5 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 6A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘，24-MLF? |
| 包装： | 标准包装 |
| 供应商设备封装： | 24-MLF?（4x4） |
| 其它名称： | 576-3645-6 |
Micrel, Inc.
PCB Layout Guideline
Warning!!! To minimize EMI and output noise, follow
Inductor
MIC22602
these layout recommendations.
PCB Layout is critical to achieve reliable, stable and
efficient performance. A ground plane is required to
control EMI and minimize the inductance in power,
signal and return paths.
The following guidelines should be followed to insure
proper operation of the MIC22602 converter.
IC
?
?
?
?
Keep the inductor connection to the switch node
(SW) short.
Do not route any digital lines underneath or close to
the inductor.
Keep the switch node (SW) away from the feedback
(FB) pin.
To minimize noise, place a ground plane underneath
the inductor.
?
?
?
?
?
Place the IC close to the point of load (POL).
Use fat traces to route the input and output power
lines.
The exposed pad (EP) on the bottom of the IC must
be connected to the ground.
Use several vias to connect the EP to the ground
plane, layer 2.
Signal and power grounds should be kept separate
Output Capacitor
? Use a wide trace to connect the output capacitor
ground terminal to the input capacitor ground
terminal.
? Phase margin will change as the output capacitor
value and ESR changes. Contact the factory if the
output capacitor is different from what is shown in
the BOM.
and connected at only one location.
Input Capacitor
? Place the input capacitor next.
?
The feedback trace should be separate from the
power trace and connected as close as possible to
the output capacitor. Sensing a long high current
load trace can degrade the DC load regulation.
?
?
?
?
?
?
?
?
Place the input capacitors on the same side of the
board and as close to the IC as possible.
Place a 22μF/6.3V ceramic bypass capacitor next to
each of the 4 PVIN pins.
Keep both the VIN and PGND connections short.
Place several vias to the ground plane close to the
input capacitor ground terminal, but not between the
input capacitors and IC pins.
Use either X7R or X5R dielectric input capacitors.
Do not use Y5V or Z5U type capacitors.
Do not replace the ceramic input capacitor with any
other type of capacitor. Any type of capacitor can be
placed in parallel with the input capacitor.
If a Tantalum input capacitor is placed in parallel
with the input capacitor, it must be recommended for
switching regulator applications and the operating
voltage must be derated by 50%.
In “Hot-Plug” applications, a Tantalum or Electrolytic
bypass capacitor must be used to limit the over-
voltage spike seen on the input supply with power is
suddenly applied.
Diode
? Place the Schottky diode on the same side of the
board as the IC and input capacitor.
? The connection from the Schottky diode’s Anode to
the input capacitors ground terminal must be as
short as possible.
? The diode’s Cathode connection to the switch node
(SW) must be keep as short as possible.
October 2009
18
M9999-102809-A
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2267YML TR | IC REG BUCK SYNC ADJ 2A 12MLF |
| MIC22700YML TR | IC REG BUCK SYNC ADJ 7A 24MLF |
| MIC22705YML TR | IC REG BUCK SYNC ADJ 7A 24MLF |
| MIC2285AYMT TR | IC REG BUCK SYNC ADJ 0.5A 10TMLF |
| MIC2285YML TR | IC REG BUCK SYNC ADJ 0.5A 10MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2267 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Input Current Limiting Synchronous Buck Regulator |
| MIC2267YML | 制造商:Micrel Inc 功能描述:Micrel MIC2267YML DC to DC Conversion |
| MIC2267YML TR | 功能描述:直流/直流开关调节器 USB Power Maximizer RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC2267YML-TR | 功能描述:Buck Switching Regulator IC Positive Adjustable 1V 1 Output 500mA 12-VFDFN Exposed Pad, 12-MLF? 制造商:microchip technology 系列:USB Power Maximizer? 包装:剪切带（CT） 零件状态:停产 功能:降压 输出配置:正 拓扑:降压 输出类型:可调式 输出数:1 电压 - 输入（最小值）:3V 电压 - 输入（最大值）:5.5V 电压 - 输出（最小值/固定）:1V 电压 - 输出（最大值）:5.5V 电流 - 输出:500mA 频率 - 开关:400kHz ~ 1.5MHz 同步整流器:是 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:12-VFDFN 裸焊盘，12-MLF? 供应商器件封装:12-MLF?（3x3） 标准包装:1 |
| MIC22700 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:1MHz, 7A Integrated Switch High Efficiency Synchronous Buck Regulator |
发布紧急采购，3分钟左右您将得到回复。