- 您现在的位置：买卖IC网 > Datasheet目录343 > MIC2291YD5 TR (Micrel Inc)IC LED DRIVER PHOTO FLASH TSOT-5 Datasheet资料下载
参数资料
| 型号： | MIC2291YD5 TR |
| 厂商： | Micrel Inc |
| 文件页数： | 7/10页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER PHOTO FLASH TSOT-5 |
| 标准包装： | 1 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1.05MHz ~ 1.35MHz |
| 电源电压： | 2.5 V ~ 10 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 125°C |
| 产品目录页面： | 1082 (CN2011-ZH PDF) |
| 其它名称： | 576-1077-6 |
Micrel, Inc.
Application Information
DC to DC PWM Boost Conversion
The MIC2291 is a constant frequency boost converter. It
operates by taking a DC input voltage and regulating
cur-rent through series LED’s by monitoring voltage
across the sense resistor (R2). LED current regulation is
achieved by turning on an internal switch, which draws
current through the inductor (L1). When the switch turns
off, the inductor’s magnetic ? eld collapses, causing the
current to be discharged into the output capacitor
through an external schottkey diode (D1). Regulation is
then achieved by pulse width modulation (PWM) to
maintain a constant voltage on the FB pin. This in turn
provides constant LED current.
MIC2291
Over Voltage Protection
For MLF ? package of MIC2291, there is an over voltage
protection function. If the feedback resistors are
disconnected from the circuit or the feedback pin is
shorted to ground, the feedback pin will fall to ground
potential. This will cause the MIC2291 to switch at full
duty-cycle in an attempt to maintain the feedback
voltage. As a result the output voltage will climb out of
control. This may cause the switch node voltage to
exceed its maximum voltage rating, possibly damaging
the IC and the external components. To ensure the
highest level of protection, the MIC2291 OVP pin will
shut the switch off when an over-voltage condition is
detected saving itself and other sensitive circuitry
downstream.
V IN
10μH
D1
1A/40V
Schottky
V OUT
Component Selection
Inductor
MIC2291-34xML
Inductor selection is a balance between efficiency,
stability, cost, size and rated current. For most
applications a 10μH is the recommended inductor value.
1-Cell
Li Ion
GND
VIN
EN
SW
OVP
FB
GND
3xLED
R2
C2
1μF
GND
It is usually a good balance between these
considerations.
Efficiency is affected by inductance value in that larger
inductance values reduce the peak to peak ripple
current. This has an effect of reducing both the DC
losses and the transition losses. There is also a
secondary effect of an inductors DC resistance (DCR).
The DCR of an inductor will be higher for more
inductance in the same package size. This is due to the
V IN
V IN
Figure 2. DC to DC PWM Boost Conversion
Duty Cycle Considerations
Duty cycle refers to the switch on-to-off time ratio and
can be calculated as follows for a boost regulator;
D = 1
V OUT
The duty cycle required for voltage conversion should be
less than the maximum duty cycle of 85%. Also, in light
load conditions where the input voltage is close to the
output volt-age, the minimum duty cycle can cause pulse
skipping. This is due to the energy stored in the inductor
causing the output to overshoot slightly over the
regulated output voltage. During the next cycle, the error
ampli ? er detects the output as being high and skips the
following pulse. This effect can be reduced by increasing
the minimum load or by increasing the inductor value.
Increasing the inductor value reduces peak current,
which in turn reduces energy transfer in each cycle.
longer windings required for an increase in inductance.
Since the majority of input current (minus the MIC2291
operating current) is passed through the inductor, higher
DCR inductors will reduce efficiency.
Also, to maintain stability, increasing inductor size will
have to be met with an increase in output capacitance.
This is due to the unavoidable “right half plane zero”
effect for the continuous current boost converter
topology. The frequency at which the right half plane
zero occurs can be calculated as follows;
2
frhpz =
V OUT × L × I OUT × 2 π
The right half plane zero has the undesirable effect of
increasing gain, while decreasing phase. This requires
that the loop gain is rolled off before this has signi ? cant
effect on the total loop response. This can be
accomplished by either reducing inductance (increasing
RHPZ frequency) or increasing the output capacitor
value (decreasing loop gain).
May 2007
7
M9999-051507
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2293-15YML TR | IC LED DRIVER WHITE BCKLGT 8-MLF |
| MIC2293C-34YML TR | IC LED DRIVER WHITE BCKLGT 8-MLF |
| MIC2297-42YML TR | IC LED DRIVR WHITE BCKLGT 10-MLF |
| MIC2298-15YML TR | IC LED DRIVER HIGH BRIGHT 12-MLF |
| MIC2299-15YML TR | IC LED DRIVR WHITE BCKLGT 12-MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2292 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Frequency PWM White LED Drivers with Internal Schottky Diode and OVP |
| MIC2292_05 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Frequency PWM White LED Drivers with Internal Schottky Diode and OVP |
| MIC2292_11 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Frequency PWM White LED Drivers with Internal Schottky Diode and OVP |
| MIC2292-15BML | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Frequency PWM White LED Drivers with Internal Schottky Diode and OVP |
| MIC2292-15BML TR | 功能描述:IC LED DRIVER WHITE BCKLGT 8-MLF RoHS:否 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT |
发布紧急采购，3分钟左右您将得到回复。