- 您现在的位置：买卖IC网 > Datasheet目录343 > MIC2291YD5 TR (Micrel Inc)IC LED DRIVER PHOTO FLASH TSOT-5 Datasheet资料下载
参数资料
| 型号： | MIC2291YD5 TR |
| 厂商： | Micrel Inc |
| 文件页数： | 8/10页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER PHOTO FLASH TSOT-5 |
| 标准包装： | 1 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1.05MHz ~ 1.35MHz |
| 电源电压： | 2.5 V ~ 10 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 125°C |
| 产品目录页面： | 1082 (CN2011-ZH PDF) |
| 其它名称： | 576-1077-6 |
Micrel, Inc.
Output Capacitor
A 1μF or greater output capacitor is sufficient for most
designs. An X5R or X7R dielectric ceramic capacitors
are recommended for designs with the MIC2291. Y5V
V IN
MIC2291
values may be used, but to offset their tolerance over
temperature, more capacitance is required.
VIN
SW
Diode Selection
The MIC2291 requires an external diode for operation. A
schottkey diode is recommended for most applications
PWM
EN
GND
FB
due to their lower forward voltage drop and reverse
recovery time. Ensure the diode selected can deliver the
peak inductor cur-rent, the maximum output current and
the maximum reverse voltage is rated greater than the
output voltage.
Input Capacitor
A minimum 1μF ceramic capacitor is recommended for
designing with the MIC2291. Increasing input
capacitance will improve performance and greater noise
immunity on the source. The input capacitor should be
as close as possible to the inductor and the MIC2291,
with short traces for good noise performance.
Feedback Resistors
The MIC2291 utilizes a feedback pin to compare the
output to an internal reference. The LED current is
adjusted by selecting the appropriate feedback resistor
value. The desired current can be calculated as follows;
Figure 3. PWM Dimming Method
2. Continuous dimming control is implemented by
applying a DC control voltage to the FB pin of
the MIC2291 through a series resistor as shown
in Figure 2. The LED intensity (current) can be
dynamically varied applying a DC voltage to the
FB pin. The DC voltage can come from a DAC
signal, or a ? ltered PWM signal. The advantage
of this approach is that a high frequency PWM
signal (>10kHz) can be used to control LED
intensity.
V IN
V REF
R2 =
I LED
Where VREF is equal to 95mV.
Dimming Control
VIN
EN
SW
FB
GND
5.11k
49.9k
There are two techniques for dimming control. One is
PWM dimming, and the other is continuous dimming.
1. PWM dimming control is implemented by
applying a PWM signal on EN pin as shown in
Figure 1. The MIC2291 is turned on and off by
the PWM signal. With this method, the LEDs
operate with either zero or full current. The
average LED current is increased proportionally
to the duty-cycle of the PWM signal. This
technique has high-efficiency because the IC
and the LEDs consume no current during the off
cycle of the PWM signal. Typical PWM
frequency should be between 100Hz and 10kHz.
DC
Equivalent
Figure 4. Continuous Dimming
May 2007
8
M9999-051507
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2293-15YML TR | IC LED DRIVER WHITE BCKLGT 8-MLF |
| MIC2293C-34YML TR | IC LED DRIVER WHITE BCKLGT 8-MLF |
| MIC2297-42YML TR | IC LED DRIVR WHITE BCKLGT 10-MLF |
| MIC2298-15YML TR | IC LED DRIVER HIGH BRIGHT 12-MLF |
| MIC2299-15YML TR | IC LED DRIVR WHITE BCKLGT 12-MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2292 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Frequency PWM White LED Drivers with Internal Schottky Diode and OVP |
| MIC2292_05 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Frequency PWM White LED Drivers with Internal Schottky Diode and OVP |
| MIC2292_11 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Frequency PWM White LED Drivers with Internal Schottky Diode and OVP |
| MIC2292-15BML | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Frequency PWM White LED Drivers with Internal Schottky Diode and OVP |
| MIC2292-15BML TR | 功能描述:IC LED DRIVER WHITE BCKLGT 8-MLF RoHS:否 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT |
发布紧急采购，3分钟左右您将得到回复。