- 您现在的位置：买卖IC网 > PDF目录14545 > MIC2295YD5 TR (Micrel Inc)IC REG BOOST ADJ 1.2A TSOT23-5 PDF资料下载
参数资料
| 型号： | MIC2295YD5 TR |
| 厂商： | Micrel Inc |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST ADJ 1.2A TSOT23-5 |
| 标准包装： | 1 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 最高 34V |
| 输入电压： | 2.5 V ~ 10 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.2MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 包装： | 标准包装 |
| 供应商设备封装： | TSOT-23-5 |
| 产品目录页面： | 1093 (CN2011-ZH PDF) |
| 其它名称： | 576-1080-6 |
V OUT = V REF × ?
? R1 ?
+ 1 ?
V IN
R 1 = R 2 ? ? OUT ? 1 ?
Micrel
Diode Selection
The MIC2295 requires an external diode for operation. A
Schottkey diode is recommended for most applications
due to their lower forward voltage drop and reverse
recovery time. Ensure the diode selected can deliver the
peak inductor current and the maximum reverse voltage is
rated greater than the output voltage.
Input Capacitor
A minimum 1μF ceramic capacitor is recommended for
designing with the MIC2295. Increasing input capacitance
will improve performance and greater noise immunity on
the source. The input capacitor should be as close as
possible to the inductor and the MIC2295, with short traces
for good noise performance.
Feedback Resistors
The MIC2295 utilizes a feedback pin to compare the
output to an internal reference. The output voltage is
adjusted by selecting the appropriate feedback resistor
values. The desired output voltage can be calculated as
follows;
? R2 ?
Where V REF is equal to 1.24V.
Duty-Cycle
The MIC2295 is a general-purpose step up DC-DC
converter. The maximum difference between the input
voltage and the output voltage is limited by the maximum
duty-cycle (D max ) of the converter. In the case of MIC2295,
D MAX = 85%. The actual duty cycle for a given application
can be calculated as follows:
D = 1 ?
V OUT
The actual duty-cycle, D, cannot surpass the maximum
rated duty-cycle, D max .
Output Voltage Setting
The following equation can be used to select the feedback
resistors R1 and R2 (see figure 1).
? V ?
? 1.24V ?
A high value of R2 can increase the whole system
efficiency, but the feedback pin input current (I FB ) of the gm
operation amplifier will affect the output voltage. The R2
resistor value must be less than or equal to 5k ? (R2 ≤ 5
k ? ).
Inductor Selection
In MIC2295, the switch current limit is 1.2A. The selected
inductor should handle at least 1.2A current without
saturating. The inductor should have a low DC resistor to
minimize power losses. The inductor’s value can be 4.7μH
to 10μH for most applications.
MIC2295
Capacitor Selection
Multi-layer ceramic capacitors are the best choice for input
and output capacitors. They offer extremely low ESR,
allowing very low ripple, and are available in very small,
cost effective packages. X5R dielectrics are preferred. A
4.7μF to 10μF output capacitor is suitable for most
applications.
Diode Selection
For maximum efficiency, Schottky diode is recommended
for use with MIC2295. An optimal component selection can
be made by choosing the appropriate reverse blocking
voltage rating and the average forward current rating for a
given application. For the case of maximum output voltage
(34V) and maximum output current capability, a 40V / 1A
Schottky diode should be used.
Open-Circuit Protection
For MLF package option of MIC2295, there is an output
over-voltage protection function that clamps the output to
below 34V in fault conditions. Possible fault conditions
may include: if the device is configured in a constant
current mode of operation and the load opens, or if in the
standard application the feedback resistors are
disconnected from the circuit. In these cases the FB pin
will pull to ground, causing the MIC2295 to switch with a
high duty-cycle. As a result, the output voltage will climb
out of regulation, causing the SW pin to exceed its
maximum voltage rating and possibly damaging the IC and
the external components. To ensure the highest level of
safety, the MIC2295 has a dedicated pin, OVP, to monitor
and clamp the output voltage in over-voltage conditions.
The OVP function is offered in the 2mm x 2mm MLF - 8L
package option only. To disable OVP function, tie the
OVP pin to ground
April 2005
10
M9999-042605
(408) 955-1690
相关PDF资料 |
PDF描述 |
|---|---|
| ASC08DRTN | CONN EDGECARD 16POS .100 DIP SLD |
| ASC08DRTH | CONN EDGECARD 16POS .100 DIP SLD |
| RCM06DTBD-S664 | CONN EDGECARD 12POS R/A .156 |
| RCM06DTMN-S664 | CONN EDGECARD 12POS R/A .156 |
| MIC2296YML TR | IC REG BOOST ADJ 1.2A 8MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2295YML | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Power Density 1.2A Boost Regulator |
| MIC2295YML TR | 功能描述:直流/直流开关转换器 1.2MHz 1.2A PWM Boost Converter (Lead Free) RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MIC2295YML-TR | 功能描述:Boost Switching Regulator IC Positive Adjustable 2.5V 1 Output 1.2A (Switch) 8-VFDFN Exposed Pad, 8-MLF? 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:有效 功能:升压 输出配置:正 拓扑:升压 输出类型:可调式 输出数:1 电压 - 输入（最小值）:2.5V 电压 - 输入（最大值）:10V 电压 - 输出（最小值/固定）:2.5V 电压 - 输出（最大值）:34V（开关） 电流 - 输出:1.2A（开关） 频率 - 开关:1.2MHz 同步整流器:无 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 供应商器件封装:8-MLF?（2x2） 标准包装:1 |
| MIC2296 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Power Density 1.2A Boost Regulator |
| MIC2296_10 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High Power Density 1.2A Boost Regulator |
发布紧急采购，3分钟左右您将得到回复。