- 您现在的位置：买卖IC网 > Datasheet目录343 > MIC2297-42YML TR (Micrel Inc)IC LED DRIVR WHITE BCKLGT 10-MLF Datasheet资料下载
参数资料
| 型号： | MIC2297-42YML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR WHITE BCKLGT 10-MLF |
| 标准包装： | 1 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 525kHz ~ 675kHz |
| 电源电压： | 2.5 V ~ 10 V |
| 输出电压： | 40V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘，10-MLF? |
| 供应商设备封装： | 10-MLF?（3x3） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 125°C |
| 产品目录页面： | 1082 (CN2011-ZH PDF) |
| 其它名称： | 576-1440-6 |
Micrel
Functional Description
The MIC2297 is a constant frequency, PWM current mode
6.8μH-22μH
MIC2297
boost regulator. The MIC2297 uses peak current mode
control. The block diagram is shown above. The MIC2297
is composed of an oscillator, slope compensation ramp
generator, current amplifier, gm error amplifier, PWM
generator, and a 1.2A bipolar output transistor. The
oscillator generates a 600kHz clock. The clock’s two
functions are to trigger the PWM generator that turns on
1-Cell
Li I on
3V to 4.2V
1μF
1μF
VIN SW
EN OVP
MIC2297
BRT - 42BM L
REF FB
AGND PGND COMP
0.1μF
10
0.47μF
/50V
the output transistor and to reset the slope compensation
ramp generator. The current amplifier is used to measure
D = 1 ?
I LED =
I out <
?
( V out ? V in ) ? V ?
I peak = ? ? in ?
?
? V out
f ? 2 ? L ? I out ? ( V out ? V in )
the switch current by amplifying the voltage signal from the
internal sense resistor. The output of the current amplifier
is summed with the output of the slope compensation
ramp generator. This summed current-loop signal is fed to
one of the inputs of the PWM generator.
The gm error amplifier measures the LED current through
the external sense resistor and amplifies the error between
the detected signal and the 200mV reference voltage. The
output of the gm error amplifier provides the voltage-loop
signal that is fed to the other input of the PWM generator.
When the current-loop signal exceeds the voltage-loop
signal, the PWM generator turns off the bipolar output
transistor. The next clock period initiates the next switching
cycle, maintaining the constant frequency current-mode
PWM control. The LED current is set by the feedback
resistor:
200 mV
R FB
The Enable pin shuts down the output switching and
disables control circuitry to reduce input current-to-leakage
levels. Enable pin input current is zero at zero volts.
DC-to-DC PWM Boost Conversion
The MIC2297 is a constant-frequency boost converter. It
operates by taking a DC input voltage and regulating a
higher DC output voltage. Figure 2 shows a typical circuit.
Boost regulation is achieved by turning on an internal
switch, which draws current through the inductor (L1).
When the switch turns off, the inductor’s magnetic field
collapses. This causes the current to be discharged into
the output capacitor through an external Schottky diode
(D1). Waveforms 1 and 2 show Output Voltage ripple, SW
Voltage, and Indicator Current for 5mA and 20mA LED
current respectively. Voltage regulation is achieved by
modulating the pulse width or pulse-width modulation
(PWM).
Figure 2. Typical Application Circuit
Duty Cycle Considerations
Duty cycle refers to the switch on-to-off time ratio and can
be calculated as follows for a boost regulator:
V in
V out
However, at light loads the inductor will completely
discharge before the end of a switching cycle. The current
in the inductor reaches 0A before the end of the switching
cycle. This is known as discontinuous conduction mode
(DCM). DCM occurs when:
V in I peak
V out 2
Where
L ? f
In DCM, the duty cycle is smaller than in continuous
conduction mode. In DCM the duty cycle is given by:
D =
V in
The duty cycle required for voltage conversion should be
less than the maximum duty cycle of 95%. Also, in light
load conditions where the input voltage is close to the
output voltage, the minimum duty cycle can cause pulse
skipping. This is due to the energy stored in the inductor
causing the output to overshoot slightly over the regulated
output voltage. During the next cycle, the error amplifier
detects the output as being high and skips the following
pulse. This effect can be reduced by increasing the
minimum load or by increasing the inductor value.
Increasing the inductor value reduces peak current.
Mach 2008
8
M9999-032708
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2298-15YML TR | IC LED DRIVER HIGH BRIGHT 12-MLF |
| MIC2299-15YML TR | IC LED DRIVR WHITE BCKLGT 12-MLF |
| MIC26603YJL EV | BOARD EVAL FOR MIC26603YJL |
| MIC26901YJL EV | BOARD EVAL FOR MIC26901YJL |
| MIC2841AYMT TR | IC LED DRIVR WHITE BCKLGT 10TMLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2298 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:3.5A Minimum, 1MHz Boost High Brightness White LED Driver |
| MIC2298_11 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:3.5A Minimum, 1MHz Boost High Brightness White LED Driver |
| MIC2298-15YML | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
| MIC2298-15YML TR | 功能描述:LED照明驱动器 7W 1MHz White LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MIC2298-15YMLTR | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。