- 您现在的位置：买卖IC网 > Datasheet目录343 > MIC2297-42YML TR (Micrel Inc)IC LED DRIVR WHITE BCKLGT 10-MLF Datasheet资料下载
参数资料
| 型号： | MIC2297-42YML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR WHITE BCKLGT 10-MLF |
| 标准包装： | 1 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 525kHz ~ 675kHz |
| 电源电压： | 2.5 V ~ 10 V |
| 输出电压： | 40V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘，10-MLF? |
| 供应商设备封装： | 10-MLF?（3x3） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 125°C |
| 产品目录页面： | 1082 (CN2011-ZH PDF) |
| 其它名称： | 576-1440-6 |
I LED =
f rhpz =
Micrel
Over-Voltage Protection
The MIC2297 has an over-voltage protection function. If an
LED is disconnected from the circuit or the feedback pin is
shorted to ground, the feedback pin will fall to ground
potential. This will cause the MIC2297 to switch at full duty
cycle in an attempt to maintain the feedback voltage. As a
result, the output voltage will climb out of control. This may
cause the switch node voltage to exceed its maximum
voltage rating, possibly damaging the IC and the external
components. To ensure the highest level of protection, the
MIC2297 OVP pin will shut the switch off when an over-
voltage condition is detected, saving itself and the output
capacitor.
Brightness Control
In the MIC2297, the reference to the voltage error amplifier
is pinned out. The BRT pin and REF pin form a voltage
divider off the internal 1.245V reference. The voltage is
such that with nothing connected to the BRT pin, the REF
voltage is 0.2V and the BRT voltage is 1V. The REF
voltage is 1/5 the BRT voltage.
The minimum REF voltage with BRT pulled to ground is
typically 10mV. With a 10 ? sense resistor, the LED
current is typically 1mA with the BRT pin pulled to ground.
An analog DC voltage can be connected to the BRT pin.
The MIC2297 will create an LED current proportional to
the BRT voltage according to the following equation:
BRT
5 ? R sense
Where BRT is the voltage applied to the BRT pin, and
Rsense is the sense resistor used in the LED string. It’s
important to use a 1uF ceramic capacitor on the REF pin
to filter any noise.
An external PWM signal can be applied to the BRT for
dimming. The 1uF REF capacitor and internal BRT 124k ?
resistor form an RC that filters the voltage to the REF pin.
The LED current is proportional the PWM duty cycle
according to the following equation:
MIC2297
Component Selection
Inductor
Inductor selection is a balance between efficiency,
stability, cost, size, and rated current. For most
applications a 22 μ H is the recommended inductor value. It
is usually a good balance between these considerations.
Larger inductance values reduce the peak-to-peak ripple
current, affecting efficiency. This has the effect of reducing
both the DC losses and the transition losses. There is also
a secondary effect of an inductor’s DC resistance (DCR).
The DCR of an inductor will be higher for more inductance
in the same package size. This is due to the longer
windings required for an increase in inductance. Since the
majority of input current (minus the MIC2297 operating
current) is passed through the inductor, higher DCR
inductors will reduce efficiency. To maintain stability,
increasing inductor size will have to be met with an
increase in output capacitance. This is due to the
unavoidable “right half plane zero” effect for the continuous
current boost converter topology. The frequency at which
the right half plane zero occurs can be calculated as
follows:
V in 2
V out ? L ? I out ? 2 π
The right half plane zero has the undesirable effect of
increasing gain, while decreasing phase. This requires that
the loop gain is rolled off before this has significant effect
on the total loop response. This can be accomplished by
either reducing inductance (increasing RHPZ frequency) or
increasing the output capacitor value (decreasing loop
gain).
Output Capacitor
Output capacitor selection is also a trade-off between
performance, size, and cost. Increasing output
capacitance will lead to an improved transient response,
but also an increase in size and cost. X5R or X7R
dielectric ceramic capacitors are recommended for
I LED =
V peak ? D
5 ? R sense
designs with the MIC2297.
The output capacitor sets the frequency of the pole and
zero in the power stage. The zero is given by:
Where Vpeak is the peak PWM voltage and D is the duty
cycle of the PWM signal.
f z =
1
C ? R esr ? 2 π
For ceramic capacitors, the ESR is very small. This puts
the zero at a very high frequency where it can be ignored.
The frequency of the pole caused by the output capacitor
is given by.
f p =
I out
C ? V out ? π
Mach 2008
9
M9999-032708
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2298-15YML TR | IC LED DRIVER HIGH BRIGHT 12-MLF |
| MIC2299-15YML TR | IC LED DRIVR WHITE BCKLGT 12-MLF |
| MIC26603YJL EV | BOARD EVAL FOR MIC26603YJL |
| MIC26901YJL EV | BOARD EVAL FOR MIC26901YJL |
| MIC2841AYMT TR | IC LED DRIVR WHITE BCKLGT 10TMLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2298 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:3.5A Minimum, 1MHz Boost High Brightness White LED Driver |
| MIC2298_11 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:3.5A Minimum, 1MHz Boost High Brightness White LED Driver |
| MIC2298-15YML | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
| MIC2298-15YML TR | 功能描述:LED照明驱动器 7W 1MHz White LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MIC2298-15YMLTR | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。