- 您现在的位置：买卖IC网 > PDF目录14536 > MIC23250-3BYMT TR (Micrel Inc)IC REG BUCK SYNC 0.4A DL 10TMLF PDF资料下载
参数资料
| 型号： | MIC23250-3BYMT TR |
| 厂商： | Micrel Inc |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC 0.4A DL 10TMLF |
| 产品培训模块： | MIC23xxx HyperLight Load™ Regulators |
| 标准包装： | 1 |
| 系列： | HyperLight Load® |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 2 |
| 输出电压： | 0.9V，1.1V |
| 输入电压： | 2.7 V ~ 5.5 V |
| PWM 型： | 混合物 |
| 频率 - 开关： | 4MHz |
| 电流 - 输出： | 400mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-UFDFN，10-TMLF? |
| 包装： | 标准包装 |
| 供应商设备封装： | 10-TMLF?（2x2） |
| 产品目录页面： | 1094 (CN2011-ZH PDF) |
| 其它名称： | 576-3255-6 |
Micrel, Inc.
Functional Description
VIN
The VIN provides power to the internal MOSFETs for the
switch mode regulator along with the current limit sensing.
The VIN operating range is 2.7V to 5.5V so an input
capacitor with a minimum of 6.3V voltage rating is
recommended. Due to the high switching speed, a
minimum of 2.2μF bypass capacitor placed close to VIN
and the power ground (PGND) pin is required. Based upon
size, performance and cost, a TDK C1608X5R0J475K,
size 0603, 4.7μF ceramic capacitor is highly recommended
for most applications. Refer to the layout
recommendations for details.
AVIN
The analog VIN (AVIN) provides power to the analog
supply circuitry. AVIN and VIN must be tied together.
Careful layout should be considered to ensure high
frequency switching noise caused by VIN is reduced
before reaching AVIN. A 0.01μF bypass capacitor placed
as close to AVIN as possible is recommended. See layout
recommendations for details.
EN1/EN2
The enable pins (EN1 and EN2) control the on and off
states of outputs 1 and 2, respectively. A logic high signal
on the enable pin activates the output voltage of the
device. A logic low signal on each enable pin deactivates
the output. MIC23250 features built-in soft-start circuitry
that reduces in-rush current and prevents the output
voltage from overshooting at start up.
SW1/SW2
The switching pin (SW1 or SW2) connects directly to one
end of the inductor (L1 or L2) and provides the current
path during switching cycles. The other end of the inductor
is connected to the load and SNS pin. Due to the high
speed switching on this pin, the switch node should be
routed away from sensitive nodes.
MIC23250
SNS1/SNS2
The SNS pin (SNS1 or SNS2) is connected to the output
of the device to provide feedback to the control circuitry. A
minimum of 2.2μF bypass capacitor should be connected
in shunt with each output. Based upon size, performance
and cost, a TDK C1608X5R0J475K, size 0603, 4.7μF
ceramic capacitor is highly recommended for most
applications. In order to reduce parasitic inductance, it is
good practice to place the output bypass capacitor as
close to the inductor as possible. The SNS connection
should be placed close to the output bypass capacitor.
Refer to the layout recommendations for more details.
PGND
The power ground (PGND) is the ground path for the high
current in PWM mode. The current loop for the power
ground should be as small as possible and separate from
the Analog ground (AGND) loop. Refer to the layout
recommendations for more details.
AGND
The signal ground (AGND) is the ground path for the
biasing and control circuitry. The current loop for the signal
ground should be separate from the Power ground
(PGND) loop. Refer to the layout recommendations for
more details.
FB1/FB2 (Adjustable Output Only)
The feedback pins (FB1/FB2) are two extra pins that can
only be found on the MIC23250-AAYMT devices. It allows
the regulated output voltage to be set by applying an
external resistor network. The internal reference voltage is
0.72V and the recommended value of R BOTTOM is within
10% of 442k Ω . The R TOP resistor is the resistor from the
FB pin to the output of the device and R BOTTOM is the
resistor from the FB pin to ground. The output voltage is
calculated from the equation below. See Compensation
under the Applications Information section for
recommended feedback component values.
V OUT = 0 . 72 V ? ?
+ 1 ? ?
? R TOP
? R BOTTOM
?
?
June 2010
11
M9999-061110-E
相关PDF资料 |
PDF描述 |
|---|---|
| V72B3V3T100B3 | CONVERTER MOD DC/DC 3.3V 100W |
| V48C8T150BL2 | CONVERTER MOD DC/DC 8V 150W |
| V48C8T150BF3 | CONVERTER MOD DC/DC 8V 150W |
| V48C8T150B3 | CONVERTER MOD DC/DC 8V 150W |
| IHSM7832ER100K | INDUCTOR POWER 10UH 5.0A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC23250-AAYMT | 制造商:Micrel Inc 功能描述:Dual 400mA Buck Reg w HyperLight Load |
| MIC23250-AAYMT EV | 功能描述:电源管理IC开发工具 High Efficiency Dual 400mA Synchronous Buck Switcher - Evaluation Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MIC23250-AAYMT TR | 功能描述:直流/直流开关调节器 High Efficiency Dual 400mA Synchronous Buck Switcher RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC23250-AAYMTEV | 制造商:Micrel Inc 功能描述:Evaluation Board MIC23250-AAYMT |
| MIC23250-AAYMT-EV | 功能描述:MIC23250 HyperLight Load? DC/DC, Step Down 2, Non-Isolated Outputs Evaluation Board 制造商:microchip technology 系列:HyperLight Load? 零件状态:有效 主要用途:DC/DC，步降 输出和类型:2，非隔离 功率 - 输出:- 电压 - 输出:1.8V，1.8V 电流 - 输出:400mA，400mA 电压 - 输入:2.7 V ~ 5.5 V 稳压器拓扑:降压 频率 - 开关:4MHz 板类型:完全填充 所含物品:板 使用的 IC/零件:MIC23250 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。