- 您现在的位置：买卖IC网 > PDF目录17425 > MIC261203YJL EV (Micrel Inc)BOARD EVAL FOR MIC261203YJL PDF资料下载
参数资料
| 型号： | MIC261203YJL EV |
| 厂商： | Micrel Inc |
| 文件页数： | 24/31页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR MIC261203YJL |
| 标准包装： | 1 |
| 系列： | HyperLight Load®, SuperSwitcher IIG™ |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，隔离 |
| 输出电压： | 5V |
| 电流 - 输出： | 12A |
| 输入电压： | 5.5 ~ 28 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 600kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MIC261203 |
| 其它名称： | 576-4014 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页
Micrel, Inc.
PCB Layout Guidelines
Warning!!! To minimize EMI and output noise, follow
these layout recommendations.
PCB Layout is critical to achieve reliable, stable and
efficient performance. A ground plane is required to
control EMI and minimize the inductance in power,
signal and return paths.
Inductor
? Keep the inductor connection to the switch node
(SW) short.
? Do not route any digital lines underneath or close to
the inductor.
? Keep the switch node (SW) away from the feedback
(FB) pin.
MIC261203
The following guidelines should be followed to insure
proper operation of the MIC261203 regulator.
?
The CS pin should be connected directly to the SW
pin to accurate sense the voltage across the low-
IC
?
?
?
?
?
A 2.2μF ceramic capacitor, which is connected to
the PVDD pin, must be located right at the IC. The
PVDD pin is very noise sensitive and placement of
the capacitor is very critical. Use wide traces to
connect to the PVDD and PGND pins.
A 1.0uF ceramic capacitor must be placed right
between VDD and the signal ground SGND. The
SGND must be connected directly to the ground
planes. Do not route the SGND pin to the PGND
Pad on the top layer.
Place the IC close to the point-of-load (POL).
Use fat traces to route the input and output power
lines.
Signal and power grounds should be kept separate
and connected at only one location.
side MOSFET.
? To minimize noise, place a ground plane underneath
the inductor.
? The inductor can be placed on the opposite side of
the PCB with respect to the IC. It does not matter
whether the IC or inductor is on the top or bottom as
long as there is enough air flow to keep the power
components within their temperature limits. The
input and output capacitors must be placed on the
same side of the board as the IC.
Output Capacitor
? Use a wide trace to connect the output capacitor
ground terminal to the input capacitor ground
terminal.
? Phase margin will change as the output capacitor
value and ESR changes. Contact the factory if the
output capacitor is different from what is shown in
Input Capacitor
? Place the input capacitor next.
? Place the input capacitors on the same side of the
board and as close to the IC as possible.
?
the BOM.
The feedback trace should be separate from the
power trace and connected as close as possible to
the output capacitor. Sensing a long high current
load trace can degrade the DC load regulation.
?
Keep both the PVIN pin and PGND connections
Optional RC Snubber
?
short.
Place several vias to the ground plane close to the
?
Place the RC snubber on either side of the board
and as close to the SW pin as possible.
input capacitor ground terminal.
?
?
?
?
Use either X7R or X5R dielectric input capacitors.
Do not use Y5V or Z5U type capacitors.
Do not replace the ceramic input capacitor with any
other type of capacitor. Any type of capacitor can be
placed in parallel with the input capacitor.
If a Tantalum input capacitor is placed in parallel
with the input capacitor, it must be recommended for
switching regulator applications and the operating
voltage must be derated by 50%.
In “Hot-Plug” applications, a Tantalum or Electrolytic
bypass capacitor must be used to limit the over-
voltage spike seen on the input supply with power is
suddenly applied.
July 2011
24
M9999-071311-A
相关PDF资料 |
PDF描述 |
|---|---|
| ADP3050-EVAL | BOARD EVAL FOR ADP3050 |
| CT8BK40-M | 8" BLACK 40LB CABLE TIE |
| RLF12560T-100M7R5 | INDUCTOR PWR 10UH 20% 12560 SMD |
| M7KKK-3610J | IDC CABLE - MDG36K/MC37G/MDG36K |
| A9CAA-0606E | FLEX CABLE - AFK06A/AE06/AFH06T |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC261203YJLTR | 制造商:Micrel 功能描述:DC DC Regulator 28V 12A 28Pin 5x6mm MLF |
| MIC261203YJL-TR | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 12A 28-PowerVQFN Variant, 28-MLF? 制造商:microchip technology 系列:HyperLight Load?，SuperSwitcher IIG?? 包装:剪切带（CT） 零件状态:有效 功能:降压 输出配置:正 拓扑:降压 输出类型:可调式 输出数:1 电压 - 输入（最小值）:4.5V 电压 - 输入（最大值）:28V 电压 - 输出（最小值/固定）:0.8V 电压 - 输出（最大值）:5.5V 电流 - 输出:12A 频率 - 开关:600kHz 同步整流器:是 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:28-PowerVQFN 变式，28-MLF? 供应商器件封装:28-MLF?（5x6） 标准包装:1 |
| MIC261203-ZAYJL TR | 制造商:Micrel Inc 功能描述:IC REG BUCK SYNC ADJ 12A 28MLF |
| MIC2619YD6 | 制造商:Micrel 功能描述:1.2MHz PWM Boost Converter with OVP |
| MIC2619YD6 TR | 功能描述:直流/直流开关转换器 1.2MHz PWM Boost Converter with OVP in Thin SOT-23 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。