参数资料
| 型号： | MIC3003GFL TR |
| 厂商： | Micrel Inc |
| 文件页数： | 30/74页 |
| 文件大小： | 0K |
| 描述： | IC FOM MANAGEMENT W/CALIBR 24MLF |
| 标准包装： | 1,000 |
| 类型： | 激光二极管控制器（光纤） |
| 数据速率： | 10Gbps |
| 通道数： | 1 |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 2.3mA |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 24-VFQFN 裸露焊盘，24-MLF? |
| 供应商设备封装： | 24-MLF?（3x3） |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页
Micrel, Inc.
Temperature Measurement
The temperature-to-digital converter is built around a
switched current source and an eight-bit/nine-bit analog-
to-digital converter. The temperature is calculated by
measuring the forward voltage of a diode junction at two
different bias current levels. An internal multiplexer directs
the current source’s output to a diode junction. This data
is also used as the input to the temperature
compensation look-up tables. Each time temperature is
sampled and an updated value acquired, new corrective
values for modulation current and the APC setpoint are
read from the corresponding tables, added to the set
values, and transferred to the DACs.
Diode Faults
The MIC3003 is designed to respond in a failsafe manner
to hardware faults in the temperature sensing circuitry. If
there is a fault with the on-chip sensing diode, the
temperature data reported by the A/D converter will be
forced to its full-scale value (+127 °C). The diode fault
MIC3003GFL
Each time an updated average value is acquired, a new
offset value for the APC setpoint is read from the
corresponding look-up table (see Table 17) and transferred
to the APC circuitry. This is illustrated in Equation 11. In a
same way, new offset values are taken from similar look-up
tables (see Table 18 and Table 19), added to the nominal
values and transferred into the modulation and fault
comparator DACs. The bias current high alarm threshold is
compensated using a fourth look-up table (see Table 20).
This compensation happens internally and does not affect
any host-accessible registers.
APCSETm = APCSETx + APCLUT ( T COMPm )
Table _ min ≤ T COMPm ≤ Table _ max
APCSETm = APCSETx + APCLUT (max)
T COMP > Table _ max
APCSETm = APCSETx + APCLUT (min)
flag, DFLT, will be set in OEMCFG0, TXFAULT will be
asserted, and the high temperature alarm and warning
flags will be set. The reported temperature will remain at
T COMP < Table _ min
(9)
+127 °C until the fault condition is cleared. Diode faults
may be reset by toggling TXDISABLE, as with any other
fault. Diode faults will not be detected at power up until
the first A/D conversion cycle is completed.
Temperature Compensation
Since the performance characteristics of laser diodes and
photodiodes change with operating temperature, the
MIC3003 provides a facility for temperature compensation
of the APC. loop set-point, laser modulation current, bias
current fault comparator threshold, and bias current high
alarm flag threshold. Temperature compensation is
performed using a look-up table (LUT) that stores values
If the measured temperature is greater than the maximum
table value, the highest value in each table is used. If the
measured temperature is less than the minimum, the
minimum value is used. Hysteresis is employed to further
enhance noise immunity and prevent oscillation. Each table
entry spans two degrees C. The table index will not change
unless the new temperature average results in a table index
beyond the midpoint of the next entry in either direction.
There is therefore 2 to 3°C of hysteresis on temperature
compensation changes. The table index will never oscillate
due to quantization noise as the hysteresis is much larger
than ±1 ? 2 LSB.
corresponding to each measured temperature over a
150°C span. Four identical tables reside at serial address
A4h and A6h as summarized in Table 16. Each table
entry is a signed twos complement integer that is used as
an offset to the parameter being compensated. The
default value of all table entries is zero, giving a flat
response.
The A/D converter reports a new temperature sample
each t CONV . This occurs at roughly 10 Hz when 8-bit
temperature resolution is selected. To prevent
Serial
Address
Base address
+4h
Base address
+6h
Byte
Addresses
00h–3Fh
40h–7Fh
80h–BFh
C0h–FFh
58h–63h
64h–6Fh
Function
APC Look-up Table
IMOD Look-up Table
IFLT Look-up Table
Bias High Alarm Look-up Table
APC Look-up Table (cont.)
IMOD Look-up Table (cont.)
temperature oscillation due to thermal or electrical noise,
sixteen successive temperature samples are averaged
together and used to index the LUT.s. Temperature
compensation results are therefore updated at 16xt CONV
intervals, or about 1.6 seconds. This can be expressed as
shown in Equation 8:
70h–7Bh IFLT Look-up Table (cont.)
7Ch–87h Bias High Alarm Look-up Table
(cont.)
Table 16. Temperature Compensation Look-up Tables
T COMPm =
T n + T n +1 + T n + 2 + ? ? ? T n +15
16
(8)
July 2010
30
M9999-072910-A
hbwhelp@micrel.com or (408) 955-1690
相关PDF资料 |
PDF描述 |
|---|---|
| MIC3003GML TR | IC FOM MANAGEMENT W/CALIBR 24MLF |
| MIC3172BN | IC REG BUCK BOOST INV CUK 8DIP |
| MIC33030-AYHJ TR | IC REG BUCK ADJ 0.4A 10HMLF |
| MIC33050-CYHL TR | IC REG BUCK SYNC 1V 0.6A 12MLF |
| MIC33153YHJ TR | IC REG BUCK SYNC ADJ 1.2A 14MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC3003GML | 功能描述:网络控制器与处理器 IC FOM Controller with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MIC3003GML TR | 功能描述:网络控制器与处理器 IC FOM Controller with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MIC3003GML-EVAL | 制造商:Micrel Inc 功能描述:FOM CONTROLLER WITH INTERNAL C |
| MIC3003GMLTR | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration |
| MIC3020BL | 功能描述:TOOL MINI CRIMPER FOR D SUB RoHS:否 类别:工具 >> 压接器，施用器，压力机 系列:Xcelite® 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
发布紧急采购，3分钟左右您将得到回复。