参数资料
型号: MIC3003GFL
厂商: Micrel Inc
文件页数: 25/74页
文件大小: 0K
描述: IC FOM MANAGEMENT W/CALIBR 24 ML
标准包装: 100
类型: 激光二极管控制器(光纤)
数据速率: 10Gbps
通道数: 1
电源电压: 3 V ~ 3.6 V
电流 - 电源: 2.3mA
工作温度: -40°C ~ 105°C
封装/外壳: 24-VFQFN 裸露焊盘,24-MLF?
供应商设备封装: 24-MLF?(3x3)
包装: 管件
安装类型: 表面贴装
其它名称: 576-3776-5
Micrel, Inc.
Figure 3. Internal Calibration RX Power Linear Approximation
C/ Reading the ADC Result Registers
The ADC result registers should be read as 16-bit
registers under internal calibration while under external
calibration they should be read as 8-bit or 16-bit
registers at the MSB address. For example, TX power
should be read under internal calibration as 16 bits at
address A2h: 66h–67h and under external calibration as
8 bits at address A2h: 66h. 9-bit temperature results and
12-bit receive power results should always be read as
16-bit quantities.
Reading the result registers using two-byte burst reads on
the SMBus guarantees that the two bytes are coherent
with each other—that is, they form a matched result pair.
If the two bytes were read separately, it is possible that
the internal result could be updated between the reads,
leading to an incorrect ADC result.
MIC3003GFL
RXPOT
A programmable, non-volatile digitally controlled
potentiometer is provided for adjusting the gain of the
receive power measurement signal chain in the analog
domain. Five bits in the RXPOT register are used to set
and adjust the position of potentiometer. RXPOT
functions as a programmable divider or attenuator. It is
adjustable in steps from 1:1 (no divider action) down to
1/32 in steps of 1/32. If RXPOT is set to zero, then the
divider is bypassed completely. There will be no scaling
of the input signal, and the resistor network will be
disconnected from the VRX pin. At all other settings of
RXPOT, there will be a 32k ? (typical) load seen on
VRX.
Figure 4. RXPOT Block Diagram
Laser Diode Bias Control
The MIC3003 can be configured to generate a constant
bias current using electrical feedback, or regulate
average transmitted optical power using a feedback
signal from a monitor photodiode, as shown in Figure 5.
An operational amplifier is used to control laser bias
current via the V BIAS output. The VBIAS pin can drive a
maximum of ±10mA. An external bipolar transistor
provides current gain. The polarity of the op amp’s
output is programmable with BIASREF (bit-5 in
OEMCFG1) in order to accommodate either NPN or
PNP transistors that drive common anode and common
cathode laser, respectively. Additionally, the polarity of
the feedback signal is programmable for use with either
common-emitter or emitter-follower transistor circuits.
July 2010
25
M9999-072910-A
hbwhelp@micrel.com or (408) 955-1690
相关PDF资料
PDF描述
NCP694D08HT1G IC REG LDO 0.8V 1A SOT-89-5
RMC40DRTS CONN EDGECARD 80POS DIP .100 SLD
GBM15DTBS CONN EDGECARD 30POS R/A .156 SLD
VE-27H-CW-S CONVERTER MOD DC/DC 52V 100W
VI-BWK-CV-S CONVERTER MOD DC/DC 40V 150W
相关代理商/技术参数
参数描述
MIC3003GFL TR 功能描述:网络控制器与处理器 IC FOM Controller with Internal Calibration in Ultra Small Package RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
MIC3003GFLTR 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration
MIC3003GML 功能描述:网络控制器与处理器 IC FOM Controller with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
MIC3003GML TR 功能描述:网络控制器与处理器 IC FOM Controller with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
MIC3003GML-EVAL 制造商:Micrel Inc 功能描述:FOM CONTROLLER WITH INTERNAL C