参数资料
型号: MIC3003GFL
厂商: Micrel Inc
文件页数: 38/74页
文件大小: 0K
描述: IC FOM MANAGEMENT W/CALIBR 24 ML
标准包装: 100
类型: 激光二极管控制器(光纤)
数据速率: 10Gbps
通道数: 1
电源电压: 3 V ~ 3.6 V
电流 - 电源: 2.3mA
工作温度: -40°C ~ 105°C
封装/外壳: 24-VFQFN 裸露焊盘,24-MLF?
供应商设备封装: 24-MLF?(3x3)
包装: 管件
安装类型: 表面贴装
其它名称: 576-3776-5
Micrel, Inc.
Serial Port Operation
The MIC3003 uses standard write byte, read byte, and
read word operations for communication with its host. It
also supports block write and block read transactions.
The write byte operation involves sending the devices
address (with the R/W bit low to signal a write operation),
followed by the address of the register to be operated
upon and the data byte. The read byte operation is a
composite write and read operation: the host first sends
the devices address followed by the register address, as
in a write operation. A new start bit must then be sent to
the MIC3003, followed by a repeat of the device address
with the R/W bit (LSB) set to the high (read) state. The
data to be read from the part may then be clocked out. A
read word is similar, but two successive data bytes are
clocked out rather than one. These protocols are shown
in Figures 21 to 24.
The MIC3003 will respond to up to four sequential device
addresses depending upon whether it is in OEM or User
mode. A match between one of the MIC3003’s addresses
and the address specified in the serial bit stream must be
made to initiate communication. The MIC3003 responds
to device addresses A0 h and A2 h in User Mode; it also
responds to A4 h and A6 h in OEM Mode (assuming the
base address is A0 h ).
MIC3003GFL
Block Writes
To increase the speed of block writes, the MIC3003 allows
up to eight consecutive bytes to be written before the
internal memory update begins.
The block write sequence begins just like a write byte
operation with the host sending the device address, R/W bit
low, register address, etc. After the first data byte is sent
the host will receive an acknowledge. Up to seven more
bytes can be sent in sequence. The MIC3003 will
acknowledge each one and increment its internal address
register in anticipation of the next byte. After the last byte is
sent, the host issues a STOP. The MIC3003’s internal write
process then begins.
Block writes of up to eight bytes can begin and end at any
byte address without restriction. Block writes that increment
over register address FFh will simply “wrap around” and
continue at address 00h within the same device address
space.
To accelerate calibration and testing, NVRAM write cycles
can be disabled completely by setting the WRINH bit in
OEMCAL0. Writes to registers that do not have NVRAM
backup, will not incur write-cycle delays when writes are
inhibited. Write operations on registers that exist only in
NVRAM will still incur write cycle delays.
Figure 21. Write Byte Protocol
Figure 22. Read Byte Protocol
Figure 23. Read_Word Protocol
July 2010
38
M9999-072910-A
hbwhelp@micrel.com or (408) 955-1690
相关PDF资料
PDF描述
NCP694D08HT1G IC REG LDO 0.8V 1A SOT-89-5
RMC40DRTS CONN EDGECARD 80POS DIP .100 SLD
GBM15DTBS CONN EDGECARD 30POS R/A .156 SLD
VE-27H-CW-S CONVERTER MOD DC/DC 52V 100W
VI-BWK-CV-S CONVERTER MOD DC/DC 40V 150W
相关代理商/技术参数
参数描述
MIC3003GFL TR 功能描述:网络控制器与处理器 IC FOM Controller with Internal Calibration in Ultra Small Package RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
MIC3003GFLTR 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration
MIC3003GML 功能描述:网络控制器与处理器 IC FOM Controller with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
MIC3003GML TR 功能描述:网络控制器与处理器 IC FOM Controller with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
MIC3003GML-EVAL 制造商:Micrel Inc 功能描述:FOM CONTROLLER WITH INTERNAL C