- 您现在的位置：买卖IC网 > Datasheet目录343 > MIC4129YME (Micrel Inc)IC MOSFET DRIVER 6A INVERT 8SOIC Datasheet资料下载
参数资料
| 型号： | MIC4129YME |
| 厂商： | Micrel Inc |
| 文件页数： | 8/10页 |
| 文件大小： | 0K |
| 描述： | IC MOSFET DRIVER 6A INVERT 8SOIC |
| 标准包装： | 95 |
| 配置： | 低端 |
| 输入类型： | 反相 |
| 延迟时间： | 45ns |
| 电流 - 峰： | 6A |
| 配置数： | 1 |
| 输出数： | 1 |
| 电源电压： | 4.5 V ~ 20 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 供应商设备封装： | 8-SOIC-EP |
| 包装： | 管件 |
| 产品目录页面： | 1109 (CN2011-ZH PDF) |
| 其它名称： | 576-1446 |
MIC4120/4129
Capacitive Load Power Dissipation
Dissipation caused by a capacitive load is simply the energy
placed in, or removed from, the load capacitance by the
driver. The energy stored in a capacitor is described by the
equation:
E = 1/2 C V 2
As this energy is lost in the driver each time the load is charged
or discharged, for power dissipation calculations the 1/2 is
removed. This equation also shows that it is good practice
not to place more voltage on the capacitor than is necessary,
as dissipation increases as the square of the voltage applied
to the capacitor. For a driver with a capacitive load:
Micrel, Inc.
Transition Power Dissipation
Transition power is dissipated in the driver each time its out -
put changes state, because during the transition, for a very
brief interval, both the N- and P-channel MOSFETs in the
output totem-pole are ON simultaneously, and a current is
conducted through them from V +S to ground. The transition
power dissipation is approximately:
P T = 2 f V S (A?s)
where (A?s) is a time-current factor derived from the typical
characteristic curves.
Total power (P D ) then, as previously described is:
where:
P L = f C (V S ) 2
P D = P L + P Q +P T
Definitions
f = Operating Frequency
C = Load Capacitance
V S = Driver Supply Voltage
Inductive Load Power Dissipation
For inductive loads the situation is more complicated. For
the part of the cycle in which the driver is actively forcing
current into the inductor, the situation is the same as it is in
the resistive case:
P L1 = I 2 R O D
However, in this instance the R O required may be either
the on resistance of the driver when its output is in the high
state, or its on resistance when the driver is in the low state,
depending on how the inductor is connected, and this is still
only half the story. For the part of the cycle when the induc -
tor is forcing current through the driver, dissipation is best
described as
P L2 = I V D (1-D)
where V D is the forward drop of the clamp diode in the driver
(generally around 0.7V). The two parts of the load dissipation
must be summed in to produce P L
P L = P L1 + P L2
Quiescent Power Dissipation
Quiescent power dissipation (P Q , as described in the input
section) depends on whether the input is high or low. A low
input will result in a maximum current drain (per driver) of
≤0.2mA; a logic high will result in a current drain of ≤2.0mA.
Quiescent power can therefore be found from:
P Q = V S [D I H + (1-D) I L ]
where:
C L = Load Capacitance in Farads.
D = Duty Cycle expressed as the fraction of time the
input to the driver is high.
f = Operating Frequency of the driver in Hertz.
I H = Power supply current drawn by a driver when both
inputs are high and neither output is loaded.
I L = Power supply current drawn by a driver when both
inputs are low and neither output is loaded.
I D = Output current from a driver in Amps.
P D = Total power dissipated in a driver in Watts.
P L = Power dissipated in the driver due to the driver ’s
load in Watts.
P Q = Power dissipated in a quiescent driver in Watts.
P T = Power dissipated in a driver when the output
changes states (“shoot-through current”) in Watts.
NOTE: The “shoot-through” current from a dual
transition (once up, once down) for both drivers
is shown by the "Typical Characteristic Curve":
Crossover Area vs. Supply Voltage and is in am -
pere-seconds. This figure must be multiplied by
the number of repetitions per second (frequency)
to find Watts.
R O = Output resistance of a driver in Ohms.
V S = Power supply voltage to the IC in Volts.
I H =
I L =
D =
V S =
quiescent current with input high
quiescent current with input low
fraction of time input is high (duty cycle)
power supply voltage
M9999-072010
8
July 2010
相关PDF资料 |
PDF描述 |
|---|---|
| MIC4223YM | IC MOSFET DVR DUAL-INV 4A 8-SOIC |
| MIC4417YM4 TR | IC DRIVER MOSF LOW SIDE SOT143-4 |
| MIC4420ZT | IC DRIVER MOSFET 6A LS TO-220-5 |
| MIC4422AYN | IC DRIVER MOSFET 9A LS 8-DIP |
| MIC4422ZT | IC DRIVER MOSFET 9A LS TO-220-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC4129YME TR | 功能描述:功率驱动器IC Improved 6A Hi-Speed, Hi-Current Single MOSFET Driver (Inverting) (Pb-Free) RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MIC4129YML | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:6A-Peak Low-Side MOSFET Driver |
| MIC4129YML TR | 功能描述:功率驱动器IC Improved 6A Hi-Speed, Hi-Current Single MOSFET Driver (Inverting) (Pb-Free) RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MIC4129YML-TR | 功能描述:IC DRIVER MOSFET 6A INVERT 8-MLF 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:有效 驱动配置:低压侧 通道类型:单路 驱动器数:1 栅极类型:N 沟道，P 沟道 MOSFET 电压 - 电源:4.5 V ~ 20 V 逻辑电压?- VIL，VIH:0.8V，2.4V 电流 - 峰值输出（灌入，拉出）:6A，6A 输入类型:反相 高压侧电压 - 最大值（自举）:- 上升/下降时间（典型值）:12ns，13ns 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 供应商器件封装:8-MLF?（2x2） 标准包装:1 |
| MIC4223 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Dual 4A, 4.5V to 18V, 15ns Switch Time, Low-Side MOSFET Drivers with Enable |
发布紧急采购，3分钟左右您将得到回复。