- 您现在的位置：买卖IC网 > PDF目录19708 > MIC49150-1.8BR TR (Micrel Inc)IC REG LDO 1.8V 1.5A SPAK-5 PDF资料下载
参数资料
| 型号： | MIC49150-1.8BR TR |
| 厂商： | Micrel Inc |
| 文件页数： | 9/13页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V 1.5A SPAK-5 |
| 标准包装： | 750 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V |
| 输入电压： | 最高 6.5V |
| 电压 - 压降（标准）： | 0.28V @ 1.5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1.5A |
| 电流 - 限制（最小）： | 1.6A |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SPAK-5 |
| 供应商设备封装： | S-PAK-5 |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC49150-1.8BRTR MIC49150-1.8BRTR-ND |
? ? ( θ JC + θ CS )
θ SA = ? ?
P D
?
?
Micrel, Inc.
Application Information
The MIC49150 is an ultra-high performance, low-dropout
linear regulator designed for high current applications
requiring fast transient response. The MIC49150 utilizes
two input supplies, signi ? cantly reducing dropout
voltage, perfect for low-voltage, DC-to-DC conversion.
The MIC49150 requires a minimum of external comp-
onents and obtains a bandwidth of up to 10MHz. As a
μCap regulator, the output is tolerant of virtually any type
of capacitor including ceramic type and tantalum type
capacitors.
The MIC49150 regulator is fully protected from damage
due to fault conditions, offering linear current limiting and
thermal shutdown.
Bias Supply Voltage
V BIAS , requiring relatively light current, provides power to
the control portion of the MIC49150. V BIAS requires
approximately 33mA for a 1.5A load current. Dropout
conditions require higher currents. Most of the biasing
current is used to supply the base current to the pass
transistor. This allows the pass element to be driven into
saturation, reducing the dropout to 300mV at a 1.5A load
current. Bypassing on the bias pin is recommended to
improve performance of the regulator during line and
load transients. Small ceramic capacitors from V BIAS to
ground help reduce high frequency noise from being
injected into the control circuitry from the bias rail and
are good design practice. Good bypass techniques
typically include one larger capacitor such as 1μF
ceramic and smaller valued capacitors such as 0.01μF
or 0.001μF in parallel with that larger capacitor to
decouple the bias supply. The V BIAS input voltage must
be 1.6V above the output voltage with a minimum V BIAS
input voltage of 3 volts.
Input Supply Voltage
VIN provides the high current to the collector of the pass
transistor. The minimum input voltage is 1.4V, allowing
con-version from low voltage supplies.
Output Capacitor
The MIC49150 requires a minimum of output capaci-
tance to maintain stability. However, proper capacitor
selection is important to ensure desired transient
response. The MIC49150 is speci ? cally designed to be
stable with virtually any capacitance value and ESR. A
1μF ceramic chip capacitor should satisfy most app-
lications. Output capacitance can be increased without
bound. See “ Typical Characteristic ” for examples of load
transient response.
X7R dielectric ceramic capacitors are recommended
because of their temperature performance. X7R-type
capacitors change capacitance by 15% over their
operating temperature range and are the most stable
MIC49150
type of ceramic capacitors. Z5U and Y5V dielectric
capacitors change value by as much as 50% and 60%
respectively over their operating temperature ranges. To
use a ceramic chip capacitor with Y5V dielectric, the
value must be much higher than an X7R ceramic or a
tantalum capacitor to ensure the same capacitance
value over the operating temperature range. Tantalum
capacitors have a very stable dielectric (10% over their
operating temperature range) and can also be used with
this device.
Input Capacitor
An input capacitor of 1μF or greater is recommended
when the device is more than 4" away from the bulk
supply capacitance, or when the supply is a battery.
Small, surface-mount, ceramic chip capacitors can be
used for the bypassing. The capacitor should be placed
within 1" of the device for optimal performance. Larger
values will help to improve ripple rejection by bypassing
the input to the regulator, further improving the integrity
of the output voltage.
Thermal Design
Linear regulators are simple to use. The most
complicated design parameters to consider are thermal
characteristics. Thermal design requires the following
application-speci ? c parameters:
? Maximum ambient temperature (T A )
? Output current (I OUT )
? Output voltage (V OUT )
? Input voltage (V IN )
? Ground current (I GND )
First, calculate the power dissipation of the regulator
from these numbers and the device parameters from this
datasheet.
P D = V IN × I IN + V BIAS × I BIAS – V OUT × I OUT
The input current will be less than the output current at
high output currents as the load increases. The bias
current is a sum of base drive and ground current.
Ground current is constant over load current. Then the
heat sink thermal resistance is determined with this
formula:
? T J(MAX) ? T A ?
?
The heat sink may be signi ? cantly reduced in
applications where the maximum input voltage is known
and large compared with the dropout voltage. Use a
series input resistor to drop excessive voltage and
distribute the heat between this resistor and the
regulator. The low-dropout properties of the MIC49150
allow signi ? cant reductions in regulator power dissipation
and the associated heat sink without compromising
performance. When this technique is employed, a
November 2006
9
M9999-111306
相关PDF资料 |
PDF描述 |
|---|---|
| CR1616 | BATTERY LITHIUM COIN 3V 16MM |
| MIC49150-1.8BR | IC REG LDO 1.8V 1.5A SPAK-5 |
| LC5512MC-75F484I | IC XPLD 512MC 7.5NS 484FPBGA |
| ISL6141IB | IC CTRLR HOT PLUG NEG VOLT 8SOIC |
| HCC50DREI-S93 | CONN EDGECARD 100PS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC49150BMM | 功能描述:IC REG LDO ADJ 1.5A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC49150BMM TR | 功能描述:IC REG LDO ADJ 1.5A 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC49150BR | 功能描述:IC REG LDO ADJ 1.5A 5SPAK RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC49150BR TR | 功能描述:IC REG LDO ADJ 1.5A SPAK-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC49150WR | 功能描述:低压差稳压器 - LDO Dual Supply, LV 1.5A LDO(ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。