- 您现在的位置：买卖IC网 > Datasheet目录343 > MIC5013YN (Micrel Inc)IC DRIVER MOSFET HI/LO SIDE 8DIP Datasheet资料下载
参数资料
| 型号： | MIC5013YN |
| 厂商： | Micrel Inc |
| 文件页数： | 12/15页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER MOSFET HI/LO SIDE 8DIP |
| 标准包装： | 50 |
| 配置： | 高端或低端 |
| 输入类型： | 非反相 |
| 延迟时间： | 60µs |
| 配置数： | 1 |
| 输出数： | 1 |
| 电源电压： | 7 V ~ 32 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 产品目录页面： | 1110 (CN2011-ZH PDF) |
| 其它名称： | 576-1232 |
MIC5013
Applications Information (Continued)
The top-side driver is based on the bootstrapped circuit of
Figure 6, and cannot be switched on inde?nitely. The boot-
strap capacitor (1μF) relies on being pulled to ground by the
bottom-side output to recharge. This limits the maximum
duty cycle to slightly less than 100%.
Two of these circuits can be connected together to form
an H-bridge. If the H-bridge is used for locked antiphase
control, no special considerations are necessary. In the case
of sign/magnitude control, the “sign” leg of the H-bridge
should be held low (PWM input held low) while the other
leg is driven by the magnitude signal.
If current feedback is required for torque control, it is avail-
able in chopped form at the bottom-side driver's 22 mΩ
current-sensing resistor.
Time-Delay Relay (Figure 12). The MIC5013 forms the
basis of a simple time-delay relay. As shown, the delay
commences when power is applied, but the 100 kΩ/1N4148
could be independently driven from an external source such
Micrel, Inc.
as a switch or another high-side driver to give a delay rela-
tive to some other event in the system.
Hysteresis has been added to guarantee clean switching
at turn-on. Note that an over-current condition latches the
relay in a safe, OFF condition. Operation is restored by
either cycling power or by momentarily shorting pin 1 to
ground.
Motor Driver with Stall Shutdown (Figure 13). Tachometer
feedback can be used to shut down a motor driver circuit
when a stall condition occurs. The control switch is a 3-way
type; the “START” position is momentary and forces the
driver ON. When released, the switch returns to the “RUN”
position, and the tachometer ’s output is used to hold the
MIC5013 input ON. If the motor slows down, the tach output
is reduced, and the MIC5013 switches OFF. Resistor “R”
sets the shutdown threshold. If the output current exceeds
30A, the MIC5013 shuts down and remains in that condition
until the momentary “RESET” button is pushed. Control is
then returned to the START/RUN/STOP switch.
15V
100nF
1N5817
1N4148
22k ?
220pF
20k ?
MIC5013
1 Input Fault 8
2 Thresh V+ 7
3 Sense Gate 6
+
1μF
1N4001 (2)
4 Source Gnd 5
IRF541
15k ?
100 ?
22m ?
CP S L - 3
(Dale)
M 10A Stalled
PWM
INPUT
15V
12V,
22k ?
2N3904
10k ?
1nF
10k ?
MIC5013
1 Input Fault 8
2 Thresh V+ 7
3 Sense Gate 6
4 Source Gnd 5
+
10μF
IRF541
22m ?
CP S L - 3
(Dale)
Figure 11. Half-Bridge
Motor Driver
MIC5013
12
July 2005
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5014YN | IC DRIVER MOSFET HI/LO SIDE 8DIP |
| MIC5016BWM | IC DRIVER MOSF DUAL HI/LO 16SOIC |
| MIC5018YM4 TR | IC DRIVER MOSFET HI SIDE SOT143 |
| MIC5020YM | IC DRIVER MOSF LO SIDE HS 8-SOIC |
| MIC5021YN | IC DRIVER MOSFET HI SIDE HS 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5014 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low-Cost High- or Low-Side MOSFET Driver |
| MIC5014_05 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low-Cost High- or Low-Side MOSFET Driver |
| MIC5014-1 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low-Cost High- or Low-Side MOSFET Driver Final Information |
| MIC5014BM | 功能描述:IC DRIVER MOSF HI/LO SIDE 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| MIC5014BM TR | 功能描述:IC DRIVER MOSF HI/LO SIDE 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
发布紧急采购，3分钟左右您将得到回复。