- 您现在的位置：买卖IC网 > Datasheet目录344 > MIC5020YM (Micrel Inc)IC DRIVER MOSF LO SIDE HS 8-SOIC Datasheet资料下载
参数资料
| 型号： | MIC5020YM |
| 厂商： | Micrel Inc |
| 文件页数： | 5/8页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER MOSF LO SIDE HS 8-SOIC |
| 标准包装： | 95 |
| 配置： | 低端 |
| 输入类型： | 非反相 |
| 延迟时间： | 400ns |
| 配置数： | 1 |
| 输出数： | 1 |
| 电源电压： | 11 V ~ 50 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 产品目录页面： | 1110 (CN2011-ZH PDF) |
| 其它名称： | 576-1818-5 MIC5020YM-ND |
MIC5020
Functional Description
Refer to the MIC5020 block diagram.
Input
A signal greater than 1.4V (nominal) applied to the MIC5020
INPUT causes gate enhancement on an external MOSFET
turning the external MOSFET on.
An internal pull-down resistor insures that an open INPUT
remains low, keeping the external MOSFET turned off.
Gate Output
Rapid rise and fall times on the GATE output are possible
because each input state change triggers a one-shot which
activates a high-value current sink (10I 2 ) for a short time.
This draws a high current through a current mirror circuit
causing the output transistors to quickly charge or discharge
the external MOSFET’s gate.
A second current sink continuously draws the lower value
of current used to maintain the gate voltage for the selected
state.
An internal 15V Zener diode protects the external MOSFET
by limiting the gate output voltage when V DD is connected
to higher voltages.
Overcurrent Limiting
Current source I 1 charges C INT upon power up. An optional
external capacitor connected to C T is discharged through
Applications Information
The MIC5020 MOSFET driver is intended for low-side switch-
ing applications where higher supply voltage, overcurrent
sensing, and moderate speed are required.
Supply Voltage
A feature of the MIC5020 is that its supply voltage rating of
up to 50V is higher than many other low-side drivers.
The minimum supply voltage required to fully enhance an
N-channel MOSFET is 11V.
A lower supply voltage may be used with logic level MOS-
FETs. Approximately 6V is needed to provide 5V of gate
enhancement.
Low-Side Switch Circuit Advantages
A moderate-speed low-side driver is generally much faster
than a comparable high-side driver. The MIC5020 can pro-
vide the gate drive switching times and low propagation delay
times that are necessary for high-frequency high-ef?ciency
circuit operation in PWM (pulse width modulation) designs
used for motor control, SMPS (switch mode power supply)
and heating element control. Switched loads (on/off) can
bene?t from the MIC5020’s fast switching times by allowing
use of MOSFETs with smaller safe operating areas. (Larger
MOSFETs are often required when using slower drivers.)
Overcurrent Limiting
A 50mV comparator is provided for current sensing. The low
level trip point minimizes I 2 R losses when power resistors
are used for current sensing. Flexibility in choosing drain or
source side sensing is provided by access to both SENSE +
Micrel, Inc.
MOSFET Q1.
A fault condition (> 50mV from SENSE + to SENSE – ) causes
the overcurrent comparator to enable current sink 2I 1 which
overcomes current source I 1 to discharge C INT in a short time.
When C INT is discharged, the INPUT is disabled, which turns
off the GATE output; the FAULT output is enabled; and C INT
and C T are ready to be charged.
When the GATE output turns the MOSFET off, the overcurrent
signal is removed from the sense inputs which deactivates
current sink 2I 1 . This allows C INT and the optional capacitor
connected to C T to recharge. A Schmitt trigger delays the
retry while the capacitor(s) recharge. Retry delay is increased
by connecting a capacitor to C T (optional).
The retry cycle will continue until the the fault is removed or
the input is changed to TTL low.
If C T is connected to ground, the circuit will not retry upon a
fault condition.
Fault Output
The FAULT output is an open collector transistor. FAULT is
active at approximately the same time the output is disabled
by a fault condition (5μs after an overcurrent condition is
sensed). The FAULT output is open circuit (off) during each
successive retry (5μs).
and SENSE – comparator inputs.
The adjustable retry feature can be used to handle loads
with high initial currents, such as lamps, motors, or heating
elements and can be adjusted from the C T connection.
C T to ground causes maintained gate drive shutdown follow-
ing overcurrent detection.
C T open, or through a capacitor to ground, causes automatic
retry . The default duty cycle (C T open) is approximately
20%. Refer to the electrical characteristics when selecting
a capacitor for a reduced duty cycle.
C T through a pull-up resistor to V DD increases the duty cycle.
Increasing the duty cycle increases the power dissipation in
the load and MOSFET. Circuits may become unstable at a
duty cycles of about 75% or higher, depending on the condi-
tions. Caution: The MIC5020 may be damaged if the voltage
on C T exceeds the absolute maximum rating.
An overcurrent condition is externally signaled by an open
collector ( FAULT ) output.
The MIC5020 may be used without current sensing by con-
necting SENSE + and SENSE – to ground.
Current Sense Resistors
Lead length can be signi?cant when using low value (< 1Ω)
resistors for current sensing. Errors caused by lead length
can be avoided by using four-terminal current sensing re-
sistors. Four-terminal resistors are available from several
manufacturers.
July 2005
5
MIC5020
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5021YN | IC DRIVER MOSFET HI SIDE HS 8DIP |
| MIC5400BWM | IC LED DRIVER RGB 28-SOIC |
| MKP1V240RL | SIDAC BIDIR 0.9A 240V DO-41 |
| MKP3V240RL | SIDAC BIDIRECT 1A 240V DO-201AD |
| MKP9V160RL | SIDAC BIDIR 0.9A 160V DO-41 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5020YM TR | 功能描述:功率驱动器IC High Speed Low Side MOSFET Driver - Lead Free RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MIC5020YM | 制造商:Micrel Inc 功能描述:ICSingle MOSFET DriverSOP8PINPLASTIC |
| MIC5021 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High-Speed High-Side MOSFET Driver |
| MIC5021_05 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:High-Speed High-Side MOSFET Driver |
| MIC5021BM | 功能描述:IC DRIVER MOSFET HISIDE HS 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
发布紧急采购，3分钟左右您将得到回复。