- 您现在的位置：买卖IC网 > PDF目录22289 > MIC5191BMM (Micrel Inc)IC REG CTRLR SGL POS ADJ 10MSOP PDF资料下载
参数资料
| 型号： | MIC5191BMM |
| 厂商： | Micrel Inc |
| 文件页数： | 10/15页 |
| 文件大小： | 845K |
| 描述： | IC REG CTRLR SGL POS ADJ 10MSOP |
| 标准包装： | 100 |
| 类型： | 正，可调式 |
| 输出数： | 1 |
| 输出电压： | 可调 |
| 电流 - 电源： | 15mA |
| 输入电压： | 1 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 管件 |
Micrel, Inc.
MIC5191
December 2006
10
M9999-122206
compensation resistor, creating a higher mid-band gain.
-20
0
20
40
60
80
100
0.01
0.1
1
10
100
1000 10000 100000
Frequency (KHz)
-45
0
45
90
135
180
225
Increasing Cout reduces
the load resistance and
output capacitor pole
allowing for an increase
in mid-band gain
Figure 7. Increasing Output Capacitance
This will have the effect of both decreasing the voltage
drop as well as returning closer and faster to the
regulated voltage during the recovery time.
MOSFET Selection
The typical pass element for the MIC5191 is an N-
Channel MOSFET. There are multiple considerations
when choosing a MOSFET. These include:
" V
IN
to V
OUT
differential
" Output Current
" Case Size/Thermal Characteristics
" Gate Capacitance (C
ISS
<10nF)
" Gate to Source threshold
The V
IN(min)
to V
OUT
ratio and current will determine the
maximum R
DSON
required. For example, for a 1.8V (?%)
to 1.5V conversion at 5A of load current, dropout voltage
can be calculated as follows (using V
IN(min)
:
(
)
OUT
OUT
IN
DSON
I
V
V
R
=
(
)
5A
V
5
.
1
1.71V
R
DSON
=
R
DSON
= 42m&
For performance reasons, we do not want to run the N-
Channel in dropout. This will seriously affect transient
response and PSRR (power supply ripple rejection). For
this reason, we want to select a MOSFET that has lower
than 42m& for our example application.
Size is another important consideration. Most import-
antly, the design must be able to handle the amount of
power being dissipated.
The amount of power dissipated can be calculated as
follows (using V
IN(max)
):
P
D
= (V
IN
V
OUT
) ?I
OUT
P
D
= (1.89V 1.5V) ?5A
P
D
= 1.95W
Now that we know the amount of power we will be
dissipating, we will need to know the maximum ambient
air temperature. For our case were going to assume a
maximum of 65癈 ambient temperature, though different
MOSFETs have different maximum operating junction
temperatures. Most MOSFETs are rated to 150癈, while
others are rated as high as 175癈. In this case, were
going to limit our maximum junction temperature to
125癈. The MIC5191 has no internal thermal protection
for the MOSFET so it is important that the design
provides margin for the maximum junction temperature.
Our design will maintain better than 125癈 junction
temperature with 1.95W of power dissipation at an
ambient temperature of 65癈. Our thermal resistance
calculates as follows:
D
J
J
JA
P
(ambient)
T
(max)
T
?/DIV>
=
1.95W
C
65
C
125
?/DIV>
JA
?/DIV>
?/DIV>
=
?/DIV>
JA
= 31癈 /W
So our package must have a thermal resistance less
than 31癈 /W. Table 1 shows a good approximation of
power dissipation and package recommendation.
Package
Power Dissipation
TSOP-6
<850mW
TSSOP-8
<950mW
TSSOP-8
<1W
PowerPAK" 1212-8
<1.1W
SO-8
<1.125W
PowerPAK" SO-8 D-Pack
<1.4W
TO-220/TO-263 (D
2
pack)
>1.4W
Table 1. Power Dissipation and
Package Recommendation
In our example, our power dissipation is greater than
1.4W, so well choose a TO-263 (D
2
Pack) N-Channel
MOSFET. ?/DIV>
JA
is calculated as follows:
?/DIV>
JA
= ?/DIV>
JC
+ ?/DIV>
CS
+ ?/DIV>
SA
Where ?/DIV>
JC
is the junction to case resistance, ?/DIV>
CS
is the
case-to-sink resistance and the ?/DIV>
SA
is the sink-to-ambi-
ent air resistance.
In the D
2
package weve selected, the ?/DIV>
JC
is 2癈/W. The
?/DIV>
CS
, assuming we are using the PCB as the heat sink,
can be approximated to 0.2癈/W. This allows us to
calculate the minimum ?/DIV>
SA
:
?/DIV>
SA
= ?/DIV>
JA
?/DIV>
CS
?/DIV>
JC
?/DIV>
SA
= 31癈/W 0.2癈/W 2癈/W
?/DIV>
SA
= 28.8癈/W
相关PDF资料 |
PDF描述 |
|---|---|
| RPR50-11012D-1 | CONV DC/DC 50W 40-160VIN 12VOUT |
| RPR50-11012D | CONV DC/DC 50W 40-160VIN 12VOUT |
| AISC-1008-R010J-T | INDUCTOR WW CERAM 10.0NH 1008 |
| MIC5190BMM | IC REG CTRLR SGL POS ADJ 10MSOP |
| R12P209D/P/R8 | CONV DC/DC 2W 12VIN +/-09VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5191BMM TR | 功能描述:IC REG CTRLR SGL POS ADJ 10-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性晶体管驱动器 系列:- 产品培训模块:More Information on LDOs 标准包装:2,500 系列:- 类型:正，固定式 输出数:2 输出电压:2.8V，3.3V 电流 - 电源:12mA 输入电压:5 V ~ 22 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MIC5191YML | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Ultra High-Speed, High-Current Active Filter / LDO Controller |
| MIC5191YML TR | 功能描述:低压差控制器 - LDO Ultra Hi-Speed Hi-Current Active Filter/LDO Controller(Lead Free) RoHS:否 制造商:Micrel 最大输入电压:5.5 V 输出电压:Adjustable 输出电流:10 mA 负载调节: 输出类型:Adjustable, Fixed 输出端数量:1 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-6 |
| MIC5191YML-TR | 功能描述:Linear Regulator Controller IC Positive Adjustable 1 Output 10-MLF? (3x3) 制造商:microchip technology 系列:- 包装:* 零件状态:停产 类型:正，可调式 输出数:1 电流 - 电源:15mA 电压 - 输入:1 V ~ 5.5 V 工作温度:-40°C ~ 125°C 封装/外壳:10-VFDFN 裸露焊盘，10-MLF? 供应商器件封装:10-MLF?（3x3） 标准包装:1 |
| MIC5191YMM | 功能描述:低压差控制器 - LDO Ultra Hi-Speed Hi-Current Active Filter/LDO Controller(Lead Free) RoHS:否 制造商:Micrel 最大输入电压:5.5 V 输出电压:Adjustable 输出电流:10 mA 负载调节: 输出类型:Adjustable, Fixed 输出端数量:1 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-6 |
发布紧急采购，3分钟左右您将得到回复。