- 您现在的位置：买卖IC网 > PDF目录19505 > MIC61150-10YML (Micrel Inc)IC REG LDO 1V 1.5A 10-MLF PDF资料下载
参数资料
| 型号： | MIC61150-10YML |
| 厂商： | Micrel Inc |
| 文件页数： | 12/22页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1V 1.5A 10-MLF |
| 标准包装： | 100 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1V |
| 输入电压： | 1.1 V ~ 3.6 V |
| 电压 - 压降（标准）： | 0.075V @ 1.5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1.5A |
| 电流 - 限制（最小）： | 1.7A |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘，10-MLF? |
| 供应商设备封装： | 10-MLF?（3x3） |
| 包装： | 管件 |
| 其它名称： | 576-3761-5 |
Micrel, Inc.
Functional Description
The MIC61150 is an ultra-high-performance, low-dropout
linear regulator designed for high-current applications
that require low input voltage operation. The MIC61150
operates from a single input supply and generates an
internal supply that is higher than the input voltage to
drive an on-chip N-Channel MOSFET. The N-Channel
MOSFET significantly reduces the dropout voltage when
compared to a traditional P-Channel MOSFET.
P-Channel MOSFETs are usually used in single-supply
low-dropout linear voltage regulators. However, for input
voltages below 1.5V, there is not sufficient gate drive to
turn on the P-Channel. To solve this issue, the
MIC61150 uses a simple internal charge pump to drive
the internal N-Channel MOSFET’s gate higher than the
input voltage, see Functional Diagram. The N-Channel
MOSFET greatly reduces the dropout voltage for the
same die area when compared to that of a P-Channel.
Other added benefits of the charge pump include the
ability to control the output voltage rise time and to
improve the power supply rejection ratio (PSRR). This is
accomplished by using the V CP supply to power the error
amplifier.
The other significant advantage of the MIC61150 over a
P-Channel regulator is its transient response. The N-
Channel in the follower configuration is much faster than
its P-channel counter part and is simpler to compensate.
Any type of output capacitor can be placed in parallel
with it as long as the minimum value output ceramic
capacitor is placed next to the MIC61150. See the
Output Capacitor section for specific details. Also, the
regulator is fully protected from damage due to fault
conditions by offering linear current limiting and thermal
shutdown.
Soft-Start
Soft-start reduces the power supply input surge current
at startup by controlling the output voltage rise time. The
input surge appears while the output capacitor is
charged up. A slower output rise time will draw a lower
input surge current.
The CP pin is the output of the internal charge pump.
The soft-start rise time is controlled by the external
capacitor connected from CP pin to GND. During soft-
start, the charge pump feeds a current to C CP . The
output voltage rise time is dependent upon the value of
C CP , the input voltage, output voltage and the current
limit. The value of the charge pump external capacitor
selected is recommended in the range of 0.1μF to 1μF,
although larger value capacitors can be used for a
longer turn-on time.
MIC61150
Input Capacitor
A 10μF ceramic input capacitor is all that is required for
most applications. However, fast load transient and low
headroom (V IN – V OUT ) requires additional bulk bypass
capacitance to ensure that the regulator does not drop
out of regulation.
The input capacitor must be placed on the same side of
the board and next to the MIC61150 to minimize the
dropout voltage and voltage ringing during transient and
short circuit conditions. It is also recommended to use
two vias for each end of the capacitor to connect to the
power and ground plane.
X7R or X5R dielectric ceramic capacitors are
recommended because of their temperature
performance. X7R-type capacitors change capacitance
by 15% over their operating temperature range and are
the most stable type of ceramic capacitors. Z5U and
Y5V dielectric capacitors change value by as much as
50% and 60% respectively over their operating
temperature ranges. To use a ceramic chip capacitor
with Y5V dielectric, the value must be much higher than
an X7R ceramic or a tantalum capacitor to ensure the
same capacitance value over the operating temperature
range. Tantalum capacitors have a very stable dielectric
(10% over their operating temperature range) and can
also be used in parallel with the ceramic capacitor(s).
See Typical Characteristics section for examples of load
transient response.
Output Capacitor
As part of the frequency compensation, the MIC61150
requires a 22μF ceramic output capacitor. However, any
other type of capacitor can be placed in parallel as long
as the 22μF ceramic output capacitor is placed next to
the MIC61150.
Output voltages below 0.8V require either a 47μF or
2x 22μF output capacitance for large output transients.
The increased output capacitance reduces the output
voltage drop caused by load transients, which increases
as a percentage of the output voltage as the output
voltage is lowered.
The output capacitor type and placement criteria are the
same as the input capacitor. See the Input Capacitor
section for a detailed description.
Minimum Load Current
The MIC61150 requires a minimum load of 10mA to
maintain output voltage regulation.
November 2010
12
M9999-112210-A
相关PDF资料 |
PDF描述 |
|---|---|
| RS3JB-13-F | DIODE FAST REC 3A 600V SMB |
| DE09S064TLF | CONN DSUB RECEPT 9POS SOLDERCUP |
| FAN7601BGX | IC PWM CTLR CURRENT MODE 10SSOP |
| HBM15DRUH | CONN EDGECARD 30POS .156 DIP SLD |
| GBB15DHLN | CONN EDGECARD 30POS .050 DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC61150-10YML TR | 功能描述:低压差稳压器 - LDO Low VIN, Single Supply, 1.5A LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC61150-10YML-TR | 功能描述:Linear Voltage Regulator IC Positive Fixed 1 Output 1V 1.5A 10-MLF? (3x3) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 稳压器拓扑:正，固定式 电压 - 输出:1V 电流 - 输出:1.5A 电压 - 跌落（典型值）:0.075V @ 1.5A 稳压器数:1 电压 - 输入:1.1 V ~ 3.6 V 电流 - 限制（最小值）:1.7A 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘，10-MLF? 供应商器件封装:10-MLF?（3x3） 标准包装:1 |
| MIC61150-10YMME | 功能描述:低压差稳压器 - LDO Low VIN, Single Supply, 1.5A LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC61150-10YMME TR | 功能描述:低压差稳压器 - LDO Low VIN, Single Supply, 1.5A LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC61150YML | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low Input Voltage, Single-Supply High-Current LDO |
发布紧急采购，3分钟左右您将得到回复。