参数资料
型号: MIC61150-10YML
厂商: Micrel Inc
文件页数: 14/22页
文件大小: 0K
描述: IC REG LDO 1V 1.5A 10-MLF
标准包装: 100
稳压器拓扑结构: 正,固定式
输出电压: 1V
输入电压: 1.1 V ~ 3.6 V
电压 - 压降(标准): 0.075V @ 1.5A
稳压器数量: 1
电流 - 输出: 1.5A
电流 - 限制(最小): 1.7A
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 10-VFDFN 裸露焊盘,10-MLF?
供应商设备封装: 10-MLF?(3x3)
包装: 管件
其它名称: 576-3761-5
makes it ideal for the 3mm × 3mm MLF package. Also,
Micrel, Inc.
To determine the maximum power dissipation allowed
that would not exceed the IC’s maximum junction
temperature (125 ° C) when operating at a maximum
ambient temperature of 75 ° C by:
P D(MAX) = (T J(MAX) – T A ) / θ JA
= (125 ° C ? 75 ° C) / (60.7 ° C/W)
MIC61150
To avoid this messy thermal couple grease or glue, an
infrared thermometer is recommended. Most infrared
thermometers’ spot size are too large for an accurate
reading on small form factor ICs. However, an IR
thermometer from Optris has a 1mm spot size, which
?
get the optional stand. The stand makes it easy to hold
the beam on the IC for long periods of time.
= 0.824W
Eq. 6
Enable
Thermal Measurements
It is always wise to measure the IC’s case temperature
to make sure that it is within its operating limits. Although
this might seem like a very elementary task, it is very
easy to get erroneous results. The most common
mistake is to use the standard thermal couple that
comes with the thermal voltage meter. This thermal
couple wire gauge is large, typically 22 gauge, and
behaves like a heatsink, resulting in a lower case
measurement.
There are two suggested methods for measuring the IC
case temperature: a thermal couple or an infrared
thermometer. If a thermal couple is used, it must be
constructed of 36 gauge wire or higher to minimize the
wire heatsinking effect. In addition, the thermal couple tip
must be covered in either thermal grease or thermal glue
to make sure that the thermal couple junction is making
good contact to the case of the IC. This thermal couple
from Omega (5SC-TT-K-36-36) is adequate for most
applications.
The MIC61150 features an active high enable input (EN)
that allows ON/OFF control of the regulator. The current
through the device reduces to near “zero” when the
device is shutdown, with only microamperes of leakage
current. The EN input may be directly tied to V IN or
driven by a voltage that is higher than V IN as long as the
voltage does not exceed the maximum operating rating
of the EN pin.
November 2010
14
M9999-112210-A
相关PDF资料
PDF描述
RS3JB-13-F DIODE FAST REC 3A 600V SMB
DE09S064TLF CONN DSUB RECEPT 9POS SOLDERCUP
FAN7601BGX IC PWM CTLR CURRENT MODE 10SSOP
HBM15DRUH CONN EDGECARD 30POS .156 DIP SLD
GBB15DHLN CONN EDGECARD 30POS .050 DIP SLD
相关代理商/技术参数
参数描述
MIC61150-10YML TR 功能描述:低压差稳压器 - LDO Low VIN, Single Supply, 1.5A LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MIC61150-10YML-TR 功能描述:Linear Voltage Regulator IC Positive Fixed 1 Output 1V 1.5A 10-MLF? (3x3) 制造商:microchip technology 系列:- 包装:剪切带(CT) 零件状态:停产 稳压器拓扑:正,固定式 电压 - 输出:1V 电流 - 输出:1.5A 电压 - 跌落(典型值):0.075V @ 1.5A 稳压器数:1 电压 - 输入:1.1 V ~ 3.6 V 电流 - 限制(最小值):1.7A 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘,10-MLF? 供应商器件封装:10-MLF?(3x3) 标准包装:1
MIC61150-10YMME 功能描述:低压差稳压器 - LDO Low VIN, Single Supply, 1.5A LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MIC61150-10YMME TR 功能描述:低压差稳压器 - LDO Low VIN, Single Supply, 1.5A LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MIC61150YML 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low Input Voltage, Single-Supply High-Current LDO