参数资料
| 型号： | MIC68200-3.3YML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V 1A 10MLF |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 5.5V |
| 电压 - 压降（标准）： | 0.3V @ 2A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1A |
| 电流 - 限制（最小）： | 2A |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘，10-MLF? |
| 供应商设备封装： | 10-MLF?（3x3） |
| 包装： | 标准包装 |
| 产品目录页面： | 1109 (CN2011-ZH PDF) |
| 其它名称： | 576-2896-6 |
Micrel, Inc.
Tracking Configurations
Normal Tracking
In normal tracking the Slave RC pin is driven from the
Master output. The internal control buffering assures
that the output of the Slave is always slightly above
the Master to guarantee that the Slave properly
regulates (based on its own internal reference) if
Master and Slave are both fixed voltage devices of the
same output voltage. The schematic and plot below
show a 1.2 volt device tracking a 1.8 volt device
through the entire turn-on / turn-off sequence. Note
that since the RC pin will overdrive the target voltage
(to assure proper regulation) the ramp down delay is
longer than the POR delay during turn-on.
Fixed Voltage Devices
10K
MIC68200
Fixed voltage versions of MIC68200 have two internal
voltage dividers: one for setting the output voltage and
the other for driving the tracking circuitry. Adjustable
parts have up to two external dividers: one from
output to SNS (to set the output voltage) and one from
the output to the Slave RC pin (in tracking
configurations). Also, the RC pin in fixed parts
operates at the same voltage as the output, whereas
the RC pin in adjustable parts operates at the 0.5V
reference. To setup a normal tracking configuration,
the divider driving the Slave RC pin is the same ratio
(or nearly the same – if both Master and Slave are set
to the same output voltage, the Slave RC divider
should be adjusted 2% to 4% higher) as the divider
driving the Slave SNS pin. This is shown below.
Adjustable Voltage devices
10K
U1
Master
U1
V IN = 2.5V
EN
1nF
1nF
MIC68200-1.8YML
IN OUT
EN SNS
RC
DLY GND POR
VOUT1
4.7μF
V IN = 3.3V
EN
2nF
1nF
MIC68200YML
IN OUT
EN SNS
RC Master
DLY GND POR
10.0K
2.50K
1.0K
383 Ω
VOUT1
4.7μF
U2
Slave
U2
Slave
NC
MIC68200-1.2YML
IN OUT
EN SNS
RC
DLY GND POR
VOUT2
4.7μF
POR
NC
MIC68200YML
IN OUT
EN SNS
RC
DLY GND POR
10.0K
3.83K
VOUT2
4.7μF
POR
February 2011
14
M9999-022311-E
相关PDF资料 |
PDF描述 |
|---|---|
| LFEC3E-4FN256C | IC FPGA 3.1KLUTS 160I/O 256-BGA |
| LFEC3E-4F256C | IC FPGA 3.1KLUTS 160I/O 256-BGA |
| LFEC3E-3F256I | IC FPGA 3.1KLUTS 160I/O 256-BGA |
| HSC43DRYI | CONN EDGECARD 86POS DIP .100 SLD |
| GSC31DTEF | CONN EDGECARD 62POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC68200YML | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
| MIC68200YML TR | 功能描述:低压差稳压器 - LDO 2A Peak FPGA/CPLD LDO with POR, Ramp Control and Sequencing RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC68200YML-TR | 功能描述:Linear Voltage Regulator IC Positive Adjustable 1 Output 0.5 V ~ 5.5 V 1A 10-MLF? (3x3) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:有效 稳压器拓扑:正，可调式 电压 - 输出:0.5 V ~ 5.5 V 电流 - 输出:1A 电压 - 跌落（典型值）:0.3V @ 2A 稳压器数:1 电压 - 输入:1.65 V ~ 5.5 V 电流 - 限制（最小值）:2A 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘，10-MLF? 供应商器件封装:10-MLF?（3x3） 标准包装:1 |
| MIC68220 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Dual 2A LDO Regulator |
| MIC68220_10 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Dual 2A LDO Regulator |
发布紧急采购，3分钟左右您将得到回复。