- 您现在的位置：买卖IC网 > PDF目录13134 > MIC706N (Micrel Inc)IC SUPERVISOR 4.4V VTH 8-DIP PDF资料下载
参数资料
| 型号： | MIC706N |
| 厂商： | Micrel Inc |
| 文件页数： | 6/7页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR 4.4V VTH 8-DIP |
| 标准包装： | 50 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 复位： | 低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 4.4V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
MIC705/06/07/08
Applications Information
Battery Switchover Section
The MIC691/693 monitors the supply voltage applied to the
V CC pin. Whenever V CC falls below the reset threshold voltage
and V BATT , the device enters battery-backup mode. When this
happens, the auxiliary supply on V BATT is routed through a
low impedance PMOS switch to the VOUT pin. The V OUT pin
is capable of sourcing up to 25mA when in the backup mode.
V CC is routed to V OUT through a large PMOS switch during
normal operation (V CC > V BATT ) and can source continuous
currents of up to 250mA. V OUT can be used to drive CMOS
RAM. The BATT ON Pin can be used to indicate the status
of battery backup mode or as the base drive for an external
pass transistor when V OUT has to source more than 25mA
in battery-backup mode. V CC is connected to V OUT and the
substrate whenever V CC exceeds the reset threshold. If
V BATT is connected to a voltage source that is greater than
0.6V above V CC , the parasitic diode of the V BATT switch will
conduct from the V BATT to the substrate.
Microprocessor Reset
The /RESET pin is asserted whenever V CC falls below the
reset threshold voltage. The reset pin remains asserted for a
period of 200ms after VCC has risen above the reset thresh-
old voltage. The reset timeout period can also be selected
by the end user, see Table 1. The reset function ensures the
microprocessor is properly reset and powers up into a known
condition after a power failure. /RESET will remain valid with
VCC as low as 1.4V and when auxiliary power is connected
to VBATT (VBATT > 2.0V), the reset pin will remain valid with
VCC from 0V to 5.5V.
Chip Enable Gating
The MIC691/693 also include memory protection circuitry
which inhibits the writing of memory during a power fail con-
dition. During normal operation, chip enable transitions are
gated througha series transmission gate from /CE IN to /CE
OUT. The typical propagation delay through the chip enable
gating circuitry is 2ns. /CE OUT follows /CE IN unless V CC
drops below the reset threshold voltage, at which time /CE OUT
will remain high until V CC returns to a valid level. EEPROMs
can be write protected in a similar manner by connecting the
/CE OUT pin to the store or write input.
Micrel, Inc.
Power Fail Warning
An additional comparator which is independent of the other
functions on the MIC691/693 is provided for early warning
of power failure. An external voltage divider can be used to
compare unregulated DC to an internal 1.25V reference. The
voltage divider ratio on the input of the power-fail comparator
(PFI) can be chosen so as to trip the power fail comparator a
few milliseconds before V CC falls below the maximum reset
threshold voltage. The output of the power-fail comparator
(/PFO) can be used to interrupt the microprocessor when
used in this mode and execute shut-down procedures prior
to power loss. Hysteresis can be added to this comparator
with external resistors, as is commonly done with any com-
parator. When VCC < VBATT - 1.2V (typ.), the power-fail
comparator is turned off and /PFO is pulled low in order to
conserve power.
Unregulated DC
R1
PFI
+
PFO
1.25V -
R2
Power Fail Comparator
Watchdog Timer
The microprocessor can be monitored by connecting the
WDI pin (watchdog input) to a bus line or an I/O line. If a
transition doesn't occur on the WDI pin with in the watchdog
timeout (Table 1.), the microprocessor is reset. /RESET will
remain asserted for 200ms when this occurs. A minimum
pulse of 100ns or any transition low-to-high or high-to-low
on the WDI pin will reset the watchdog timer. The output of
the watchdog timer (WDO) will remain high, if WDI sees a
valid transition within the watchdog period or if VCC falls
below the reset threshold as the watchdog timer is disabled
when this happens.
MIC705/06/07/08
6
January 2006
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B3V-EY-F3 | CONVERTER MOD DC/DC 5.8V 50W |
| MAX734ESA+ | IC SUPPLY PROG MEM 8-SOIC |
| ESA35DRMT-S288 | CONN EDGECARD 70POS .125 EXTEND |
| VE-J1H-CX | CONVERTER MOD DC/DC 52V 75W |
| RCM22DTKT | CONN EDGECARD 44POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC706P | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:μP Supervisory Circuit |
| MIC706P_06 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:レP Supervisory Circuit |
| MIC706PM | 功能描述:IC SUPERVISOR 2.63V VTH 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:标准传输延迟为 60 µs 电压 - 阀值:3V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 其它名称:LM8364BALMF30DKR |
| MIC706PM TR | 功能描述:IC SUPERVISOR 2.63V VTH 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:标准传输延迟为 60 µs 电压 - 阀值:3V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 其它名称:LM8364BALMF30DKR |
| MIC706PMY | 功能描述:监控电路 P Supervisor, Watchdog Timer, Active Hi, 2.63V VTH, SOIC-08 (Lead Free) RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。