- 您现在的位置：买卖IC网 > PDF目录18735 > MICRF505BML TR (Micrel Inc)TXRX ISM 868-915MHZ 32-MLF PDF资料下载
参数资料
| 型号： | MICRF505BML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 28/42页 |
| 文件大小： | 0K |
| 描述： | TXRX ISM 868-915MHZ 32-MLF |
| 标准包装： | 1,000 |
| 频率： | 850MHz ~ 950MHz |
| 数据传输率 - 最大： | 200kbps |
| 调制或协议： | FSK |
| 应用： | 遥测，无线控制器 |
| 功率 - 输出： | 10dBm |
| 灵敏度： | -111dBm |
| 电源电压： | 2.3 V ~ 5.5 V |
| 电流 - 接收： | 13.5mA |
| 电流 - 传输： | 28mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘，32-MLF? |
| 包装： | 带卷 (TR) |
| 其它名称： | MICRF505BMLTR MICRF505BMLTR-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
Micrel
The modulator filter will not influence the frequency
deviation as long as the programmed cut-off
frequency is above the actual bit rate.
The frequency deviation must be programmed so
that the modulation index (2 x single sided frequency
deviation/Baudrate [bps]) always is greater than or
equal to 2 including the total frequency offset
between the receiver and the transmitter:
f DEV = Baudrate + f OFFSET
The calculated f DEV should be used to calculate the
needed receiver bandwidth, see chapter Switched
capacitor filter.
Using the XCO-tune Bits
The RF chip has a built-in mechanism for tuning the
frequency of the crystal oscillator and is often used
in combination with the Frequency Error Estimator
(FEE). The XCO tuning is designed to eliminate or
reduce initial frequency tolerance of the crystal
and/or the frequency stability over temperature. If
the value in XCO_tune is increased (adding
capacitance), the frequency will decrease.
MICRF505BML/YML
XCO_tune value and vice versa for FEE < 0.
FEE field holds a number in the range -128, … ,
127. However, it keeps counting above/below the
range, which is:
If FEE = -128 and still counting dwn-pulses:
1) =>-129 = +127
2) 126
3) 125
…
To avoid this situation, always make sure max count
is between limits. Suggestion: Count for 8 (or 16)
bits only.
Procedure description:
In the procedure below, UP+DWN pulses are
counted, and only the sign of the FEE is used. The
value of n is 8 or 16.
Assumption:
A transmitter is sending a 1010… pattern at the
correct frequency and bitrate.
The wanted receiver frequency is the mid-point
between the “0” and “1” frequencies.
The XCO uses two external capacitors (see figure
5). The value of these will strongly affect the tuning
range. With a 16.0 MHz crystal (TN4-26011 from
Toyocom), and external capacitor values of 1.5 pF,
Input:
Nothing
the tuning range will be approximately symmetrical
around the center frequency. A XCO_tune >16 will
decrease the frequency and vice versa (see figure
Output
The best XCO_tune
lowest IFEEI)
value
(giving
the
6).
A procedure for using the XCO_tune feature in
combination with the FEE is given below. The
MICRF505 measures the frequency offset between
the demodulated signal and the LO and tune the
XCO so the LO frequency is equal to received
carrier frequency.
A procedure like this can be called during production
(storing the calibrated XCO_tune value), at regular
intervals or implemented in the communication
protocol when the frequency has changed.
The FEE will count “UP”-pulses and “DOWN”-pulses
(pulses out of the demodulator when a logic “1” or
logic “0”, resp.., is received). The FEE can count
pulses for n bits, where n = 8, 16, 32 or 64.
Local variables:
XCO_Present: (5-bit) holds present value
in XCO_tune bits
XCO_Step: (4-bit) holds
increment/decrement of XCO_tune bits
SCO_Sign: (1 bit) holds POS or NEG
(increment/cerement) increasing LO is
done by reducing the XCO_tune value
XCO TUNE PROCEDURE
I NT:
XCO_Present = 0
XCO_Step = 32
XCO_Sign = NEG
Control_Word =
Default RX, clocks match transmitter
Example: In FEE, count UP+DOWN pulses,
counting 8 bits:
A perfect case ==> FEE = 0
If FEE > 0: LO is too low, increase LO by decreasing
LOOP:
XCO_Step = XCO_Step/2
October 2006
28
M9999-103106
+1 408-944-0800
相关PDF资料 |
PDF描述 |
|---|---|
| A-20GV21 | BASIC SWITCH |
| 7W-60.000MBB-T | OSC 60.000 MHZ 3.3V SMD |
| IXFX32N100P | MOSFET N-CH 1000V 32A PLUS247 |
| X09-019WNC | MOD RF 900MHZ 19.2K W/WIRE ANT |
| X09-019NSC-TX | MOD RF TX 900MHZ 19.2K W/RPSMA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MICRF505DEV1 | 功能描述:射频开发工具 MICRF505 Evaluation Kit - For experimental use only RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MICRF505DEV1 | 制造商:Micrel Inc 功能描述:KIT MICRF505 EVALUATION |
| MICRF505L | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:850MHz and 950MHz ISM Band Transceiver |
| MICRF505LYML | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
| MICRF505LYML TR | 功能描述:射频收发器 850MHz to 950MHz, 2.25V to 5.5V FSK Transceiver with +10dBm Power Amplifier RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。