- 您现在的位置：买卖IC网 > PDF目录18735 > MICRF506BML TR (Micrel Inc)TXRX ISM 400MHZ 32-MLF PDF资料下载
参数资料
| 型号： | MICRF506BML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 16/42页 |
| 文件大小： | 0K |
| 描述： | TXRX ISM 400MHZ 32-MLF |
| 标准包装： | 1,000 |
| 频率： | 410MHz ~ 450MHz |
| 数据传输率 - 最大： | 200kBaud |
| 调制或协议： | FSK |
| 应用： | ISM |
| 功率 - 输出： | 11dBm |
| 灵敏度： | -113dBm |
| 电源电压： | 2 V ~ 2.5 V |
| 电流 - 接收： | 12mA |
| 电流 - 传输： | 10.5mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘，32-MLF? |
| 包装： | 带卷 (TR) |
| 其它名称： | MICRF506BMLTR MICRF506BMLTR-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
Micrel
MICRF506BML/YML
The lengths of the N, M, and A registers are 12, 12
and 6 respectively The values can be calculated
from the following formula:
C L =
1
C 10
1
+
1
C 11
+ C parasitic
The parasitic
capacitance
is the
pin input
= XCO =
f VCO f RF × 2
( 16 × N + A ) × 2 ( 16 × N + A )
f PhD
where
f
M
M ≠ 0
1 ≤ A<N
=
capacitance and PCB stray capacitance. Typically,
the total parasitic capacitance is around 6pF. For
instance, for a 9pF load crystal the recommended
values of the external load capacitors are 5.6pF.
It is also possible to tune the crystal oscillator
internally by switching in internal capacitance using
5 tune bits XCOtune4 – XCOtun0. When XCOtune4
f PhD : Phase detector comparison frequency
f XCO : Crystal oscillator frequency
f VCO : Voltage controlled oscillator frequency
f RF : RF carrier frequency
There are two sets of each of the divide factors (i.e.
A0 and A1). If modulation by using the dividers is
selected (that is Modulation1=1, Modulation0=0), the
two sets should be programmed to give two RF
frequencies, separated by two times the specified
frequency deviation. For all other modulation
methods, and also in receive mode, the 0-set will be
used.
– XCOtune0 = 0 no internal capacitors are
connected to the crystal pins. When XCOtune4 –
XCOtune0 = 1 all of the internal capacitors are
connected to the crystal pins. Figure 6 shows the
tuning range for two different capacitor values, 1.5pF
and no capacitors.
The crystal used is a TN4-26011 from Toyocom.
Specification: Package TSX-10A, Nominal frequency
16.000000 MHz, frequency tolerance ±10ppm,
frequency stability ±9ppm, load capacitance 9pF,
pulling sensitivity 15ppm/pF. When the external
capacitors are set to 1.5pF and the XCOtune=16,
the total capacitance will normally be ~9pF.
Crystal Oscillator (XCO)
Adr D7 D6 D5 D4
D3
D2
D1
D0
100,0
0001001
‘0’
‘0’
‘1’
XCOtune4 XCOtune3 XCOtune2
XCOtune1
XCOtune0
80,0
60,0
The crystal oscillator is a very critical block. As the
crystal oscillator is a reference for the RF output
frequency and also for the LO frequency in the
receiver, very good phase and frequency stability is
40,0
20,0
0,0
-20,0
2x1.5pF
2x0pF
required. The schematic of the crystal oscillator’s
external components for 16MHz are shown in Figure
5.
-40,0
-60,0
0
8
16
24
32
XCO bitvalue
Pin 24
Y1
Pin 23
XTALOUT
C10
5.6pF
TSX-10A
C11
5.6pF
XTALIN
Figure 6. XCO Tuning
The start up time is given in Table 7. As can be
seen, more capacitance will slow down the start up
time.
Figure 5. Crystal Oscillator Circuit
The crystal should be connected between pins
XTALIN and XTALOUT (pin 23 and 24). In addition,
loading capacitors for the crystal are required. The
loading capacitor values depend on the total load
capacitance, C L , specified for the crystal. The load
capacitance seen between the crystal terminals
should be equal to C L for the crystal to oscillate at
the specified frequency.
The start-up time of a crystal oscillator is typically
around a millisecond. Therefore, to save current
consumption, the XCO is turned on before any other
circuit block. During start-up the XCO amplitude will
eventually reach a sufficient level to trigger the M-
counter. After counting 2 M-counter output pulses
the rest of the circuit will be turned on. The current
consumption during the prestart period is
approximately 280 μ A.
July 2006
16
M9999-092904
+1 408-944-0800
相关PDF资料 |
PDF描述 |
|---|---|
| 0622022450 | TOOL INSERT 20POS 2ROW L SERIES |
| MICRF505BML TR | TXRX ISM 868-915MHZ 32-MLF |
| A-20GV21 | BASIC SWITCH |
| 7W-60.000MBB-T | OSC 60.000 MHZ 3.3V SMD |
| IXFX32N100P | MOSFET N-CH 1000V 32A PLUS247 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MICRF506DEV1 | 功能描述:射频开发工具 MICRF506 Evaluation Kit - For experimental use only RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MICRF506DEV1 | 制造商:Micrel Inc 功能描述:KIT MICRF506 EVALUATION |
| MICRF506YML | 制造商:Micrel Inc 功能描述:410/450MHZ ITRANSCEIVER SMD MLF32 制造商:Micrel Inc 功能描述:410/450MHZ ITRANSCEIVER, SMD, MLF32 制造商:Micrel Inc 功能描述:MICRF506 Series 410-450 MHz ISM Band FSK Transceiver - MLF-32 制造商:Micrel Inc 功能描述:410/450MHZ ITRANSCEIVER, SMD, MLF32; Frequency Min:410MHz; Frequency Max:450MHz; Modulation Type:FSK; Sensitivity dBm:-113dBm; Data Rate:200Kbps; Supply Voltage Min:2V; Supply Voltage Max:2.5V; RF IC Case Style:MLF; No. of Pins:32; ;RoHS Compliant: Yes |
| MICRF506YML TR | 功能描述:射频收发器 410MHz to 470MHz, 2.0V to 2.5V, Low-Power FSK Transceiver with +10dBm Power Amplifier RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MICRF506YMLTR | 制造商:Micrel 功能描述:433MHz ISM Band Transceiver |
发布紧急采购，3分钟左右您将得到回复。