- 您现在的位置：买卖IC网 > PDF目录2098 > MK2059-01SILFTR (IDT, Integrated Device Technology Inc)IC VCXO CLK JITTER ATTEN 20-SOIC PDF资料下载
参数资料
| 型号： | MK2059-01SILFTR |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC VCXO CLK JITTER ATTEN 20-SOIC |
| 标准包装： | 1,000 |
| 类型： | 时钟频率变换器 |
| PLL： | 是 |
| 输入： | LVCMOS |
| 输出： | LVCMOS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 2:1 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 25.92MHz |
| 除法器/乘法器： | 是/无 |
| 电源电压： | 3.15 V ~ 3.45 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC |
| 包装： | 带卷 (TR) |
MK2059-01
VCXO-BASED FRAME CLOCK FREQUENCY TRANSLATOR
VCXO AND SYNTHESIZER
IDT VCXO-BASED FRAME CLOCK FREQUENCY TRANSLATOR
6
MK2059-01
REV H 051310
Crystal Load Capacitors
The device crystal connections should include pads for
small capacitors from X1 to ground and from X2 to ground,
shown as CL in the External Component Schematic. These
capacitors are used to adjust the stray capacitance of the
board to match the nominally required crystal load
capacitance. Because load capacitance can only be
increased in this trimming process, it is important to keep
stray capacitance to a minimum by using very short PCB
traces (and no via’s) been the crystal and device.
evaluation. Please refer to application note MAN05 for the
procedure to determine the capacitor values.
PCB Layout Recommendations
For optimum device performance and lowest output phase
noise, the following guidelines should be observed. Please
also refer to the Recommended PCB Layout drawing on
Page 7.
1) Each 0.01F decoupling capacitor should be mounted on
the component side of the board as close to the VDD pin as
possible. No via’s should be used between decoupling
capacitor and VDD pin. The PCB trace to VDD pin should
be kept as short as possible, as should the PCB trace to the
ground via. Distance of the ferrite bead and bulk decoupling
from the device is less critical.
2) The loop filter components must also be placed close to
the CHGP and VIN pins. CP should be closest to the device.
Coupling of noise from other system signal traces should be
minimized by keeping traces short and away from active
signal traces. Use of vias should be avoided.
3) The external crystal should be mounted just next to the
device with short traces. The X1 and X2 traces should not
be routed next to each other with minimum spaces, instead
they should be separated and away from other traces.
4) To minimize EMI the 33
series termination resistor, if
needed, should be placed close to the clock output.
5) An optimum layout is one with all components on the
same side of the board, minimizing vias through other signal
layers (the ferrite bead and bulk decoupling capacitor can be
mounted on the back). Other signal traces should be routed
away from the MK2059-01. This includes signal traces just
underneath the device, or on layers adjacent to the ground
plane layer used by the device.
The IDT Applications Note MAN05 may also be referenced
for additional suggestions on layout of the crystal section.
相关PDF资料 |
PDF描述 |
|---|---|
| MK2069-01GILFTR | IC VCXO CLK SYNCHRONIZER 56TSSOP |
| MK2069-04GILFTR | IC VCXO CLK TRANSLATOR 56-TSSOP |
| MK2302S-01LFTR | IC MULTIPLIER/ZD BUFFER 8-SOIC |
| MK2304S-2LF | IC PLL ZD BUFFER LO SKEW 8-SOIC |
| MK2703SILF | IC PLL AUD CLK SYNTHESIZER 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MK2059-01SITR | 功能描述:IC VCXO CLK JITTER ATTEN 20-SOIC RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| MK2069-01 | 制造商:ICS 制造商全称:ICS 功能描述:VCXO-Based Line Card Clock Synchronizer |
| MK2069-01GI | 功能描述:IC VCXO CLK SYNCHRONIZER 56TSSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| MK2069-01GILF | 功能描述:时钟合成器/抖动清除器 VCXO-BASED LINE CARD CLOCK SYNCHRONIZER RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| MK2069-01GILFTR | 功能描述:时钟发生器及支持产品 VCXO-BASED LINE CARD CLOCK SYNCHRONIZER RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
发布紧急采购，3分钟左右您将得到回复。