- 您现在的位置：买卖IC网 > PDF目录62583 > MK3771-17R (INTEGRATED DEVICE TECHNOLOGY INC) 108 MHz, VIDEO CLOCK GENERATOR, PDSO28 PDF资料下载
参数资料
| 型号： | MK3771-17R |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟产生/分配 |
| 英文描述： | 108 MHz, VIDEO CLOCK GENERATOR, PDSO28 |
| 封装： | 0.150 INCH, 0.025 INCH PITCH, MO-153, SSOP-28 |
| 文件页数： | 4/9页 |
| 文件大小： | 219K |
| 代理商： | MK3771-17R |
MK3771-17
VCXO AND HDTV SET-TOP CLOCK SOURCE
VCXO AND SYNTHESIZER
IDT VCXO AND HDTV SET-TOP CLOCK SOURCE
4
MK3771-17
REV E 051310
External Component Selection
The MK3771-17 requires a minimum number of external
components for proper operation.
Decoupling Capacitors
Decoupling capacitors of 0.01
F should be connected
between VDD and GND on pins 3 and 6, and on pins 13 and
14, as close to the MK3771-17 as possible. For optimum
device performance, the decoupling capacitors should be
mounted on the component side of the PCB. Avoid the use
of vias in the decoupling circuit.
Series Termination Resistor
When the PCB traces between the clock outputs and the
loads are over 1 inch, series termination should be used. To
series terminate a 50
trace (a commonly used trace
impedance) place a 33
resistor in series with the clock line,
as close to the clock output pin as possible. The nominal
impedance of the clock output is 20
.
Quartz Crystal
The MK3771-17 VCXO function consists of the external
crystal and the integrated VCXO oscillator circuit. To assure
the best system performance (frequency pull range) and
reliability, a crystal device with the recommended
parameters must be used, and the layout guidelines
discussed in the following section must be followed.
The frequency of oscillation of a quartz crystal is determined
by its “cut” and by the load capacitors connected to it. The
MK3771-17 incorporates on-chip variable load capacitors
that “pull” (change) the frequency of the crystal. The crystal
specified for use with the MK3771-17 is designed to have
zero frequency error when the total of on-chip + stray
capacitance is 14 pF.
The external crystal must be connected as close to the chip
as possible and should be on the same side of the PCB as
the MK3771-17. There should be no vias between the
crystal pins and the X1 and X2 device pins. There should be
no signal traces underneath or close to the crystal.
Please see application note MAN05 for recommended
crystal parameters and suppliers.
Crystal Tuning Load Capacitors
The crystal traces should include pads for small fixed
capacitors, one between X1 and ground, and another
between X2 and ground. Stuffing of these capacitors on the
PCB is optional. The need for these capacitors is
determined at system prototype evaluation, and is
influenced by the particular crystal used (manufacture and
frequency) and by PCB layout. The typical required
capacitor value is 1 to 4 pF.
To determine the need for and value of the crystal
adjustment capacitors, you will need a PC board of your final
layout, a frequency counter capable of about 1 ppm
resolution and accuracy, two power supplies, and some
samples of the crystals which you plan to use in production,
along with measured initial accuracy for each crystal at the
specified crystal load capacitance, CL.
To determine the value of the crystal capacitors:
1. Connect VDD of the MK3771-17 to 3.3 V. Connect pin 4
of the MK3771-17 to the second power supply. Adjust the
voltage on pin 4 to 0V. Measure and record the frequency of
the CLK output.
2. Adjust the voltage on pin 4 to 3.3 V. Measure and record
the frequency of the same output.
To calculate the centering error:
Where:
ftarget = nominal crystal frequency
errorxtal =actual initial accuracy (in ppm) of the crystal being
measured
If the centering error is less than ±25 ppm, no adjustment is
needed. If the centering error is more than 25ppm negative,
the PC board has excessive stray capacitance and a new
PCB layout should be considered to reduce stray
capacitance. (Alternately, the crystal may be re-specified to
a higher load capacitance. Contact IDT for details.) If the
centering error is more than 25ppm positive, add identical
fixed centering capacitors from each crystal pin to ground.
The value for each of these caps (in pF) is given by:
Error
10
6
x
f3.3V ftet
arg
–
()
f
0V
f
tet
arg
–
()
+
f
tet
arg
------------------------------------------------------------------------------
error
xtal
–
=
相关PDF资料 |
PDF描述 |
|---|---|
| MK5814SLF | 128 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| MK5814STR | 128 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| MK5814SLFTR | 128 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| MK5814S | 128 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| MK74CG117AF | 90 MHz, OTHER CLOCK GENERATOR, PDSO48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MK3771-17RLF | 功能描述:VCXO振荡器 VCXO AND HDTV SET-TO P CLOCK SOURCE RoHS:否 制造商:Fox 封装 / 箱体:5 mm x 3.2 mm 频率:19.2 Mhz 频率稳定性:2.5 PPM 输出格式: 封装:Reel 电源电压:3 V 端接类型:SMD/SMT 尺寸:3.2 mm W x 5 mm L x 1.5 mm H 最小工作温度:- 20 C 最大工作温度:+ 75 C |
| MK3771-17RLFTR | 功能描述:时钟发生器及支持产品 VCXO AND HDTV SET-TO P CLOCK SOURCE RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| MK3771-17RTR | 功能描述:IC VCXO/PLL CLK SYNTHESZR 28SSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| MK3801N06 | 制造商:SGS 功能描述:REV H |
| MK3801N-6 | 制造商:MOSTEK 功能描述: 制造商:STMicroelectronics 功能描述: |
发布紧急采购，3分钟左右您将得到回复。