- 您现在的位置：买卖IC网 > PDF目录16790 > MPC18730EP (Freescale Semiconductor)IC PMIC PROGR 5-OUTPUTS 64-QFN PDF资料下载
参数资料
| 型号： | MPC18730EP |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 14/35页 |
| 文件大小： | 0K |
| 描述： | IC PMIC PROGR 5-OUTPUTS 64-QFN |
| 产品变化通告： | MPC18730EP(R2) Discontinuation 04/Jun/2010 |
| 标准包装： | 260 |
| 应用： | 手持/移动设备 |
| 电流 - 电源： | 9mA |
| 电源电压： | 0.9 V ~ 4.2 V |
| 工作温度： | -10°C ~ 65°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-WFQFN |
| 供应商设备封装： | 64-QFN（9x9） |
| 包装： | 管件 |
| 配用： | KIT18730EPEVBE-ND - KIT FOR MPC18730 PMIC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 18730 power management integrated circuit provides
five independent output voltages for the micro controller from
either a single cell Li-Ion or from a single cell Ni-MH or dry
cell. The PMIC includes two DC to DC converters and three
low drop out linear regulators. The output voltage for each of
the five output voltages is set independently through a 3-wire
reset modes to minimize power consumption for portable
equipment. In single cell Li-Ion applications two DC-DC
converters are configured as buck regulators. In single cell
Ni-MH or dry cell applications, one DC-DC converter is
configured as a boost regulator, and the other as buck-boost
regulator.
serial interface. The PMIC has multiple wakeup, sleep, and
FUNCTIONAL PIN DESCRIPTION
CLEAR PIN (CLEAR)
This Clear input signal makes clear internal latches for
WAKE signal holding. The WAKE control circuit can not
receive another WAKE input until the latch is cleared by this
Clear input.
Channel-1 or Channel-2 DC/DC converter as
‘VO1_SENSEor VO2_SENSE.
VOLTAGE OUTPUT PINS (VOUT1, VOUT2)
Output ‘VO1_SENSE or ‘VO2_SENSE’ voltage controlled
internal power switch.
WAKE SIGNAL PINS (WAKE1B, WAKE2B,
WAKE3B, WAKE4B) ... ACTIVE LOW
Any one WAKE input signal of these four WAKE inputs
awakes this device from sleep mode. The WAKE signals can
be made with external low side mechanical switch and
resistance that is pulled up to VSTB rail.
LOW-SIDE SWITCH OUTPUT PIN (LSWO)
Low-Side switch output that is turned on with ‘CLEAR’
signal. It can be used for external key input latches clear.
LOW VOLTAGE BATTERY PIN (LVB)
This input pin is used for temporarily power supply while
wake up for 1cell Ni-MH battery or 1 cell dry cell battery (=
Low Voltage Battery) use. It has to be connected to VB rail.
POWER INPUT PINS (VIN1, VIN2)
The power input pins (VIN1, VIN2) are drain pins on the
top side FET of the DC/DC converter switcher. They are the
power input for the buck converter and output for the boost
converter.
SWITCHING PINS (SW1, SW2)
Switching Pins (SW1, SW2) are the output of the half
bridge and connect to the external inductance.
POWER GROUND PINS (PGND1, PGND2,
GNDGATE)
Ground level node for DC/DC converter and Charge Pump
portion.
When Li-Ion battery is used, the pin has to be open.
INVERTED RESET OUTPUT PINS (PGOOD1,
HIGH VOLTAGE BATTERY PIN (HVB)
This input pin is used for temporarily power supply while
wake up for Li-Ion battery (= High Voltage Battery) use. It has
to be connected to the VB rail. When a Ni-MH battery is used,
the pin has to be connected to ground level.
STANDBY VOLTAGE PIN (V_STDBY)
Standby Voltage is made from LVB or HVB that depends
on which battery is used. This voltage is used for internal
logic and analog circuit at standby (sleep) mode temporarily
before ‘VO1_SENSE’ voltage is established.
VOLTAGE INPUT PINS (VO1_SENSE, VO2_SENSE)
This power supply input pin named ‘VO1_SENS or
VO2_SENSE’ is for internal logic and analog circuits and for
input of ‘VOUT1’ output via power switch. Input for ‘VOUT2’
PGOOD2)
Reset signal output for external MPU or the something
controller. PGOOD1 keeps ‘Low’ level while the
VO1_SENSE voltage is less than internal reference voltage.
PGOOD2 follows to VO2_SENSE voltage.
RESET DELAY CAPACITOR PINS
(PGOOD1_DELAY, PGOOD2_DELAY)
The capacitor connected to this pin decides delay time to
negate the Reset signal from exceeding the reference
voltage level.
RESET 1 ADJUSTMENT PIN (RESET1_TH)
Used to adjust the reset level with external resistance
which is connected to VO1_SENSE for PGOOD1.
is ‘VO2_SENSE_IN’ pin. It is supplied from the output of
18730
Analog Integrated Circuit Device Data
14
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| 0982661106 | CBL 39POS 0.5MM JMPR TYPE D 6" |
| EBC22DRTN-S734 | CONN EDGECARD 44POS DIP .100 SLD |
| ISL6537CRZ | IC REG/CTLR ACPI DUAL DDR 28QFN |
| EEC30DRTH-S734 | CONN EDGECARD 60POS DIP .100 SLD |
| ECM25DCWT | CONN EDGECARD 50POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MPC18730EP | 制造商:Freescale Semiconductor 功能描述:IC POWER MANAG PROG 121MA 64QFN |
| MPC18730EP/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Power Management IC with Five Power Management IC with Five Power Management IC with Five Power Management IC with Five |
| MPC18730EPR2 | 功能描述:板上安装压力/力传感器 POWER MGT IC RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides |
| MPC18A26VMEL | 制造商:Motorola Inc 功能描述: |
| MPC190VMB | 制造商:Freescale Semiconductor 功能描述:IC SECURITY PROCESSOR 252-MAPBGA |
发布紧急采购，3分钟左右您将得到回复。