- 您现在的位置：买卖IC网 > PDF目录67997 > MPC603PFE180LX (FREESCALE SEMICONDUCTOR INC) 32-BIT, 180 MHz, RISC PROCESSOR, CQFP240 PDF资料下载
参数资料
| 型号： | MPC603PFE180LX |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, 180 MHz, RISC PROCESSOR, CQFP240 |
| 封装： | 32 X 32 MM, 4.10 MM HEIGHT, 0.50 MM PITCH, CERAMIC, QFP-240 |
| 文件页数： | 24/40页 |
| 文件大小： | 431K |
| 代理商： | MPC603PFE180LX |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
30
PID7v-603e Hardware Specifications
PRELIMINARY—SUBJECT TO CHANGE WITHOUT NOTICE
1.8.2 PLL Power Supply Filtering
The AVdd power signal is provided on the 603e to provide power to the clock generation phase-locked loop.
To ensure stability of the internal clock, the power supplied to the AVdd input signal should be ltered using
a circuit similar to the one shown in Figure 14. The circuit should be placed as close as possible to the AVdd
pin to ensure it lters out as much noise as possible. The 0.1
F capacitor should be closest to the AVdd pin,
followed by the 10
F capacitor, and nally the 10 resistor to Vdd. These traces should be kept short and
direct.
Figure 14. PLL Power Supply Filter Circuit
1.8.3 Decoupling Recommendations
Due to the 603e’s dynamic power management feature, large address and data buses, and high operating
frequencies, the 603e can generate transient power surges and high frequency noise in its power supply,
especially while driving large capacitive loads. This noise must be prevented from reaching other
components in the 603e system, and the 603e itself requires a clean, tightly regulated source of power.
Therefore, it is recommended that the system designer place at least one decoupling capacitor at each Vdd
and OVdd pin of the 603e. It is also recommended that these decoupling capacitors receive their power from
separate Vdd, OVdd, and GND power planes in the PCB, utilizing short traces to minimize inductance.
These capacitors should vary in value from 220 pF to 10
F to provide both high- and low-frequency
ltering, and should be placed as close as possible to their associated Vdd or OVdd pin. Suggested values
for the Vdd pins—220 pF (ceramic), 0.01
F (ceramic), and 0.1 F (ceramic). Suggested values for the
OVdd pins—0.01
F (ceramic), 0.1 F (ceramic), and 10 F (tantalum). Only SMT (surface mount
technology) capacitors should be used to minimize lead inductance.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,
feeding the Vdd and OVdd planes, to enable quick recharging of the smaller chip capacitors. These bulk
capacitors should also have a low ESR (equivalent series resistance) rating to ensure the quick response time
necessary. They should also be connected to the power and ground planes through two vias to minimize
inductance. Suggested bulk capacitors—100
F (AVX TPS tantalum) or 330 F (AVX TPS tantalum).
1.8.4 Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. Unused active low inputs should be tied to Vdd. Unused active high inputs should be connected to
GND. All NC (no-connect) signals must remain unconnected.
Power and ground connections must be made to all external Vdd, OVdd, and GND pins of the 603e.
1.8.5 Pull-up Resistor Requirements
The 603e requires high-resistive (weak: 10 K
) pull-up resistors on several control signals of the bus
interface to maintain the control signals in the negated state after they have been actively negated and
released by the 603e or other bus master. These signals are—TS, ABB, DBB, and ARTRY.
Vdd
AVdd
10
10
F
0
.1
F
GND
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
AR
CH
IVE
D B
Y F
RE
ES
CA
LE
SE
MI
CO
ND
UC
TO
R,
INC
.
相关PDF资料 |
PDF描述 |
|---|---|
| MPC603PFE200LX | 32-BIT, 200 MHz, RISC PROCESSOR, CQFP240 |
| MPC603PRX233LX | 32-BIT, 233 MHz, RISC PROCESSOR, CBGA255 |
| MPC603PRX160LX | 32-BIT, 160 MHz, RISC PROCESSOR, CBGA255 |
| MPC603PRX225LX | 32-BIT, 225 MHz, RISC PROCESSOR, CBGA255 |
| MPC603PFE233LX | 32-BIT, 233 MHz, RISC PROCESSOR, CQFP240 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MPC603RRX200LC | 功能描述:微处理器 - MPU 603R REV2.1 HIP3.0 RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MPC603RRX200TC | 功能描述:微处理器 - MPU 603R REV2.1 HIP3.0 RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MPC603RRX266LC | 功能描述:微处理器 - MPU 603R REV2.1 HIP3.0 RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MPC603RRX266TC | 功能描述:微处理器 - MPU 603R REV2.1 HIP3.0 RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MPC603RRX300LC | 功能描述:微处理器 - MPU 603R REV2.1 HIP3.0 RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
发布紧急采购，3分钟左右您将得到回复。