参数资料
型号: MPC852TVR50A
厂商: Freescale Semiconductor
文件页数: 4/80页
文件大小: 0K
描述: IC MPU POWERQUICC 50MHZ 256PBGA
标准包装: 60
系列: MPC8xx
处理器类型: 32-位 MPC8xx PowerQUICC
速度: 50MHz
电压: 1.8V
安装类型: 表面贴装
封装/外壳: 256-BGA
供应商设备封装: 256-PBGA(23x23)
包装: 托盘
MPC852T PowerQUICC Hardware Specifications, Rev. 4
12
Freescale Semiconductor
Power Supply and Power Sequencing
9
Power Supply and Power Sequencing
This section provides design considerations for the MPC852T power supply. The MPC852T has a core
voltage (VDDL) and PLL voltage (VDDSYN) that operates at a lower voltage than the I/O voltage VDDH.
The I/O section of the MPC852T is supplied with 3.3 V across VDDH and VSS (GND).
The signals PA[0:3], PA[8:11], PB15, PB[24:25]; PB[28:31], PC[4:7], PC[12:13], PC15] PD[3:15], TDI,
TDO, TCK, TRST, TMS, MII_TXEN, MII_MDIO are 5-V tolerant. All inputs cannot be more than 2.5 V
greater than VDDH. In addition, 5-V tolerant pins can not exceed 5.5 V, and the remaining input pins cannot
exceed 3.465 V. This restriction applies to power-on reset or power down and normal operation.
One consequence of multiple power supplies is that when power is initially applied, the voltage rails ramp
up at different rates. The rates depend on the nature of the power supply, the type of load on each power
supply, and the manner in which different voltages are derived. The following restrictions apply:
VDDL must not exceed VDDH during power-on reset or power down.
VDDL must not exceed 1.9 V, and VDDH must not exceed 3.465.
These cautions are necessary for the long-term reliability of the part. If they are violated, the electrostatic
discharge (ESD) protection diodes are forward-biased, and excessive current can flow through these
diodes. If the system power supply design does not control the voltage sequencing, the circuit shown in
Figure 3 can be added to meet these requirements. The MUR420 Schottky diodes control the maximum
potential difference between the external bus and core power supplies on power-on reset, and the 1N5820
diodes regulate the maximum potential difference on power-down.
Figure 3. Example Voltage Sequencing Circuit
10 Mandatory Reset Configurations
The MPC852T requires a mandatory configuration during reset.
If hardware reset configuration word (HRCW) is enabled, by asserting the RSTCONF during HRESET
assertion, the HRCW[DBGC] value that is needed to be set to binary X1 in the hardware reset
configuration word (HRCW) and the SIUMCR[DBGC] should be programmed with the same value in the
boot code after reset.
If hardware reset configuration word (HRCW) is disabled, by negating the RSTCONF during the
HRESET assertion, the SIUMCR[DBGC] should be programmed with binary X1 in the boot code after
reset.
VDDH
VDDL
1N5820
MUR420
相关PDF资料
PDF描述
MPC852TZT50A IC MPU POWERQUICC 50MHZ 256PBGA
XC4VLX25-10FFG676C IC FPGA VIRTEX-4 LX 25K 676-FBGA
RSC50DTES CONN EDGECARD 100POS .100 EYELET
RMC19DTEH CONN EDGECARD 38POS .100 EYELET
MPC8321VRAFDC IC MPU PWRQUICC II 516-PBGA
相关代理商/技术参数
参数描述
MPC852TVR66 功能描述:IC MPU POWERQUICC 66MHZ 256-PBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微处理器 系列:MPC8xx 标准包装:2 系列:MPC8xx 处理器类型:32-位 MPC8xx PowerQUICC 特点:- 速度:133MHz 电压:3.3V 安装类型:表面贴装 封装/外壳:357-BBGA 供应商设备封装:357-PBGA(25x25) 包装:托盘
MPC852TVR66A 功能描述:微处理器 - MPU Ethernet 66 MHz RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC852TVR66A 制造商:Freescale Semiconductor 功能描述:IC 32BIT MPU 66MHZ BGA-256
MPC852TVR80A 功能描述:微处理器 - MPU POWER QUICC II HIP6W RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC852TZT100A 功能描述:微处理器 - MPU POWER QUICC II HIP6W RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324