参数资料
型号: MPC8569EVTANKGA
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: RISC PROCESSOR, PBGA783
封装: 29 X 29 MM, 1 MM PITCH, PLASTIC, BGA-783
文件页数: 118/126页
文件大小: 2847K
代理商: MPC8569EVTANKGA
Serial RapidIO (SRIO)
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
91
2.11.3
DC Requirements for Serial RapidIO
This section explains the DC requirements for the Serial RapidIO interface.
2.11.3.1
DC Requirements for Serial RapidIO SD_REF_CLK and SD_REF_CLK
The characteristics and DC requirements of the separate SerDes reference clocks of the SRIO interface are described in
2.11.3.2
DC Serial RapidIO Timing Transmitter Specifications
The LP-serial transmitter electrical and timing specifications are given in the following sections.
The differential return loss, S11, of the transmitter in each case are better than the following:
–10 dB for (Baud Frequency)
÷ 10 < Freq(f) < 625 MHz
–10 dB + 10log(f
÷ 625 MHz) dB for 625 MHz ≤Freq(f) ≤Baud Frequency
The reference impedance for the differential return loss measurements is 100-
Ωresistive. Differential return loss includes
contributions from on-chip circuitry, chip packaging, and any off-chip components related to the driver. The output impedance
requirement applies to all valid output levels.
It is recommended that the 20%–80% rise/fall time of the transmitter, as measured at the transmitter output, in each case have
a minimum value 60 ps.
It is recommended that the timing skew at the output of an LP-serial transmitter between the two signals that comprise a
differential pair not exceed 25 ps at 1.25 GB, 20 ps at 2.50 GB, and 15 ps at 3.125 GB.
The following table defines the serial RapidIO transmitter DC specifications.
2.11.3.3
DC Serial RapidIO Receiver Specifications
The LP-serial receiver electrical and timing specifications are given in the following sections.
Receiver input impedance shall result in a differential return loss better that 10 dB and a common mode return loss better than
6 dB from 100 MHz to (0.8)
× (baud frequency). This includes contributions from on-chip circuitry, the chip package, and any
off-chip components related to the receiver. AC coupling components are included in this requirement. The reference impedance
for return loss measurements is 100-
Ωresistive for differential return loss and 25-Ω resistive for common mode.
Table 52. SRIO Transmitter DC Timing Specifications—1.25, 2.5, and 3.125 GBauds
At recommended operating conditions with XVDD = 1.0 V ± 3%. and 1.1 V ± 3%
Parameter
Symbol
Min
Typ
Max
Unit
Notes
Output voltage
VO
–0.40
2.30
V
1
Long-run differential output voltage
VDIFFPP
800
1600
mV p-p
Short-run differential output voltage
VDIFFPP
500
1000
mV p-p
Note:
1. Voltage relative to COMMON of either signal comprising a differential pair.
相关PDF资料
PDF描述
MPC8569EVTAQLJ RISC PROCESSOR, PBGA783
MPC8569VTANKGA RISC PROCESSOR, PBGA783
MPC8569VTAUNLB RISC PROCESSOR, PBGA783
MPC8308CVMAGDA RISC MICROCONTROLLER, PBGA473
MPC8308VMAFDA RISC MICROCONTROLLER, PBGA473
相关代理商/技术参数
参数描述
MPC8569EVTANKGB 功能描述:数字信号处理器和控制器 - DSP, DSC 8569 800MHz rev2.1 RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
MPC8569EVTAQLJB 功能描述:数字信号处理器和控制器 - DSP, DSC 8569 1GHz rev2.1 RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
MPC8569EVTAUNLB 功能描述:数字信号处理器和控制器 - DSP, DSC 8569 1.33GHz rev2.1 RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
MPC8569VJAUNLB 制造商:Freescale Semiconductor 功能描述:IC MPU PWRQUICC 1333MHZ 783FCBGA
MPC8569VTANKGB 功能描述:数字信号处理器和控制器 - DSP, DSC 8569 ST 800/600/400 r2.1 RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT