- 您现在的位置：买卖IC网 > PDF目录262797 > MSU2031C25 (Mosel Vitelic, Corp.) low working voltage 16 MHz ROM less MCU PDF资料下载
参数资料
| 型号： | MSU2031C25 |
| 厂商： | Mosel Vitelic, Corp. |
| 英文描述： | low working voltage 16 MHz ROM less MCU |
| 中文描述： | 低工作电压低于16兆赫ROM的单片机 |
| 文件页数： | 18/21页 |
| 文件大小： | 119K |
| 代理商： | MSU2031C25 |
6
Rev. 1.0 February 1998
MOSEL VITELIC
MSU2051/U2031
Power Down Mode
It saves the RAM content, stops the clock generator
and disables every other blocks' function until the
coming hardware reset. To save even more power
consumption, user's software program can invoke this
mode. The SFRs and the on-chip data RAM retain
their values during this mode, but the porcessor stops
executing instructions. In Power-Down mode (PD=1)
the oscillator is frozen.
-An instruction that sets flag (PCON.1) causes that to
be the last instruction executed before going into the
Power Down Mode.
-In the Power Down Mode, the on-chip oscillator is
stopped.
With the clock frozen, all functions are stopped, but
the on-chip RAM and Special Function Registers are
held.
-Reset redefines all the SFRs, but does not change the
on-chip RAM.
-There are two ways to terminate the Power Down
Mode.
1) By hardware reset
All SFR and PC value will be cleared to reset value.
2) One of CLK, DATA, PORT 2.0-2.7 transition to low
(falling edge trigger)
After the program wakes up, the PC value will be
0023h (if enable IE register) and execute interrupt
service routine and then returns to PC+1 address after
the program wakes up.
-Care must be taken, however, to ensure that VCC is
not reduced before the Power Down Mode is invoked,
and that VCC is restored to its normal operating level
before the Power Down Mode is terminated.
-The hardware reset must be held active long enough
to allow the oscillator to restart and stabilize.
General of above
User should fix the attention on using wake up from
port 2:
-The user should write the power down or idle mode
flag value to one RAM address before write PCON to
distinguish waking up from power down mode or idle
mode.
-After idle mode or power down mode wakes up, the
interrupt service routine will be executed first and then
executes PC+1 address if the IE register is enabled
before entering power down mode or idle mode. The
interrupt service routine will not be executed but CPU
executes PC+1 address program if disable IE register.
-After wake up power down or idle mode the IDF flag
will be set by hardware. The IDF flag be cleared at
the ISR execution time. If IE register is disable, the
IDF flag will not be cleared when power down or idle
mode wakes up.
Mode
Program
memory
ALE
#PSEN
Port 0
Port 1
Port 2
Port 3
Idle
Power Down
Internal
External
Internal
External
1
0
1
0
Data
Float
Data
Float
Data
Address
Data
The state of pins during Idle and Power-Down Mode
Symbol
Vdd - Vss
VIN
VOUT
T (Operating)
T (Storage)
Name
DC supply Voltage
Input voltage
output voltage
Operating Temperature
Storage Temperature
Rating
-0.5 ~ +5.0
-0.5 ~ +7.0
Vss-0.3 ~ Vdd +0.3
Vss ~ Vdd
0 ~ +70
-55 ~ +125
Unit
V
Absolute Maximal Rating
* Note:
Operation beyond Absolute Maximal Rating
can adversely affect device reliability.
°C
Remark
U20x1L
U20x1S,U20x1C
°C
相关PDF资料 |
PDF描述 |
|---|---|
| MSU2031S16 | Datamate Hand Crimp Tool |
| MSU2032C16 | low working voltage 16 MHz ROM less MCU |
| MSU2032C25 | low working voltage 16 MHz ROM less MCU |
| MSU2032C40 | low working voltage 16 MHz ROM less MCU |
| MSU2051 | low working voltage 16 MHz ROM less MCU |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MSU2031C40 | 制造商:MOSEL 制造商全称:MOSEL 功能描述:low working voltage 16 MHz ROM less MCU |
| MSU2031L16 | 制造商:MOSEL 制造商全称:MOSEL 功能描述:low working voltage 16 MHz ROM less MCU |
| MSU2031S16 | 制造商:MOSEL 制造商全称:MOSEL 功能描述:low working voltage 16 MHz ROM less MCU |
| MSU2032C16 | 制造商:MOSEL 制造商全称:MOSEL 功能描述:low working voltage 16 MHz ROM less MCU |
| MSU2032C25 | 制造商:MOSEL 制造商全称:MOSEL 功能描述:low working voltage 16 MHz ROM less MCU |
发布紧急采购，3分钟左右您将得到回复。