- 您现在的位置：买卖IC网 > PDF目录379326 > MTB50P03HDL (MOTOROLA INC) TMOS POWER FET LOGIC LEVEL 50 AMPERES 30 VOLTS PDF资料下载
参数资料
| 型号： | MTB50P03HDL |
| 厂商： | MOTOROLA INC |
| 元件分类： | JFETs |
| 英文描述： | TMOS POWER FET LOGIC LEVEL 50 AMPERES 30 VOLTS |
| 中文描述： | 50 A, 30 V, 0.03 ohm, P-CHANNEL, Si, POWER, MOSFET |
| 文件页数： | 9/12页 |
| 文件大小： | 182K |
| 代理商： | MTB50P03HDL |
9
Motorola TMOS Power MOSFET Transistor Device Data
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. Solder
stencils are used to screen the optimum amount. These
stencils are typically 0.008 inches thick and may be made of
brass or stainless steel. For packages such as the SC–59,
SC–70/SOT–323, SOD–123, SOT–23, SOT–143, SOT–223,
SO–8, SO–14, SO–16, and SMB/SMC diode packages, the
stencil opening should be the same as the pad size or a 1:1
registration. This is not the case with the DPAK and D2PAK
packages. If one uses a 1:1 opening to screen solder onto the
drain pad, misalignment and/or “tombstoning” may occur due
to an excess of solder. For these two packages, the opening
in the stencil for the paste should be approximately 50% of the
tab area. The opening for the leads is still a 1:1 registration.
Figure 18 shows a typical stencil for the DPAK and D2PAK
packages. The pattern of the opening in the stencil for the
drain pad is not critical as long as it allows approximately 50%
of the pad to be covered with paste.
Figure 18. Typical Stencil for DPAK and
D2PAK Packages
SOLDER PASTE
OPENINGS
STENCIL
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and soldering
should be 100
°
C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10
°
C.
The soldering temperature and time shall not exceed
260
°
C for more than 10 seconds.
When shifting from preheating to soldering, the maximum
temperature gradient shall be 5
°
C or less.
After soldering has been completed, the device should be
allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
* Due to shadowing and the inability to set the wave height to
incorporate other surface mount components, the D2PAK is
not recommended for wave soldering.
相关PDF资料 |
PDF描述 |
|---|---|
| MTB75N03HDL | TMOS POWER FET LOGIC LEVEL 75 AMPERES 25 VOLTS |
| MTB8N50E | TMOS POWER FET 8.0 AMPERES 500 VOLTS |
| MTD1P50E | TMOS POWER FET 1.0 AMPERES 500 VOLTS 15 OHM |
| MTD2N40E | TMOS POWER FET 2.0 AMPERES 400 VOLTS RDS(on) = 3.5 OHM |
| MTD2N50E | TMOS POWER FET 2.0 AMPERES 500 VOLTS RDS(on) = 3.6 OHM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MTB50P03HDLG | 功能描述:MOSFET PFET 30V 50A RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube |
| MTB50P03HDLT4 | 功能描述:MOSFET 30V 50A Logic Level RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube |
| MTB50P03HDLT4G | 功能描述:MOSFET PFET D2PAK 30V 50A 25mOhm RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube |
| MTB50SA | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Full-Size (7.3mm or 4.7mm height) |
| MTB50SAM | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Full-Size (7.3mm or 4.7mm height) |
发布紧急采购，3分钟左右您将得到回复。