- 您现在的位置：买卖IC网 > PDF目录188952 > MX29F400TMI-70 (MACRONIX INTERNATIONAL CO LTD) 256K X 16 FLASH 5V PROM, 70 ns, PDSO44 PDF资料下载
参数资料
| 型号： | MX29F400TMI-70 |
| 厂商： | MACRONIX INTERNATIONAL CO LTD |
| 元件分类： | PROM |
| 英文描述： | 256K X 16 FLASH 5V PROM, 70 ns, PDSO44 |
| 封装： | 0.500 INCH, PLASTIC, MO-175, SOP-44 |
| 文件页数： | 3/45页 |
| 文件大小： | 722K |
| 代理商： | MX29F400TMI-70 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
11
P/N:PM0439
MX29F400T/B
REV. 1.9, APR. 03, 2002
Q2:Toggle Bit II
The "Toggle Bit II" on Q2, when used with Q6, indicates
whether a particular sector is actively erasing (that is,
the Automatic Erase algorithm is in process), or whether
that sector is erase-suspended. Toggle Bit I is valid af-
ter the rising edge of the final WE or CE, whichever hap-
pens first, pulse in the command sequence.
Q2 toggles when the system reads at addresses within
those sectors that have been selected for erasure. (The
system may use either OE or CE to control the read
cycles.) But Q2 cannot distinguish whether the sector
is actively erasing or is erase-suspended. Q6, by com-
parison, indicates whether the device is actively eras-
ing, or is in Erase Suspend, but cannot distinguish which
sectors are selected for erasure. Thus, both status bits
are required for sectors and mode information. Refer to
Table 4 to compare outputs for Q2 and Q6.
Reading Toggle Bits Q6/ Q2
Whenever the system initially begins reading toggle bit
status, it must read Q7-Q0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, the
system would note and store the value of the toggle bit
after the first read. After the second read, the system
would compare the new value of the toggle bit with the
first. If the toggle bit is not toggling, the device has
completed the program or erase operation. The system
can read array data on Q7-Q0 on the following read cycle.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the sys-
tem also should note whether the value of Q5 is high
(see the section on Q5). If it is, the system should then
determine again whether the toggle bit is toggling, since
the toggle bit may have stopped toggling just as Q5 went
high. If the toggle bit is no longer toggling, the device
has successfully completed the program or erase op-
eration. If it is still toggling, the device did not complete
the operation successfully, and the system must write
the reset command to return to reading array data.
The remaining scenario is that system initially determines
that the toggle bit is toggling and Q5 has not gone high.
The system may continue to monitor the toggle bit and
Q5 through successive read cycles, determining the sta-
tus as described in the previous paragraph. Alterna-
tively, it may choose to perform other system tasks. In
this case, the system must start at the beginning of the
algorithm when it returns to determine the status of the
operation.
Q6:Toggle BIT I
Toggle Bit I on Q6 indicates whether an Automatic Pro-
gram or Erase algorithm is in progress or complete, or
whether the device has entered the Erase Suspend mode.
Toggle Bit I may be read at any address, and is valid
after the rising edge of the final WE or CE, whichever
happens first, pulse in the command sequence (prior to
the program or erase operation), and during the sector
time-out.
During an Automatic Program or Erase algorithm opera-
tion, successive read cycles to any address cause Q6
to toggle. The system may use either OE or CE to con-
trol the read cycles. When the operation is complete, Q6
stops toggling.
After an erase command sequence is written, if all sec-
tors selected for erasing are protected, Q6 toggles and
returns to reading array data. If not all selected sectors
are protected, the Automatic Erase algorithm erases the
unprotected sectors, and ignores the selected sectors
that are protected.
The system can use Q6 and Q2 together to determine
whether a sector is actively erasing or is erase sus-
pended. When the device is actively erasing (that is, the
Automatic Erase algorithm is in progress), Q6 toggling.
When the device enters the Erase Suspend mode, Q6
stops toggling. However, the system must also use Q2
to determine which sectors are erasing or erase-sus-
pended. Alternatively, the system can use Q7.
If a program address falls within a protected sector, Q6
toggles for approximately 2 us after the program com-
mand sequence is written, then returns to reading array
data.
Q6 also toggles during the erase-suspend-program mode,
and stops toggling once the Automatic Program algo-
rithm is complete.
Table 4 shows the outputs for Toggle Bit I on Q6.
If the output is low (Busy), the device is actively erasing
or programming. (This includes programming in the Erase
Suspend mode.) If the output is high (Ready), the de-
vice is ready to read array data (including during the
Erase Suspend mode), or is in the standby mode.
Table 4 shows the outputs for RY/BY.
相关PDF资料 |
PDF描述 |
|---|---|
| MX2J080160-2C | 4000 MHz - 8000 MHz RF/MICROWAVE FREQUENCY DOUBLER, 13 dB CONVERSION LOSS-MAX |
| MX3-8X8-I2C-13-9/LT-FC/APC-1 | FIBER OPTIC SWITCH, 1290-1330nm, 8X8PORT, FC/APC CONNECTOR |
| MX3-MXN-I2C-13-9/LT-FC/APC-1 | FIBER OPTIC SWITCH, 1290-1330nm, 8X8PORT, FC/APC CONNECTOR |
| MX3-MXN-I2C-13-9/LT-FC/SPC-1 | FIBER OPTIC SWITCH, 1290-1330nm, 8X8PORT, FC/SPC CONNECTOR |
| MX3-MXN-I2C-13-9/LT-FC/SPC-X | FIBER OPTIC SWITCH, 1290-1330nm, 8X8PORT, FC/SPC CONNECTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MX29F400TTA-12 | 制造商:MCNIX 制造商全称:Macronix International 功能描述:4M-BIT [512Kx8/256Kx16] CMOS FLASH MEMORY |
| MX29F400TTA-90 | 制造商:MCNIX 制造商全称:Macronix International 功能描述:4M-BIT [512Kx8/256Kx16] CMOS FLASH MEMORY |
| MX29F400TTC-12 | 制造商:MCNIX 制造商全称:Macronix International 功能描述:4M-BIT [512Kx8/256Kx16] CMOS FLASH MEMORY |
| MX29F400TTC-55 | 制造商:MCNIX 制造商全称:Macronix International 功能描述:4M-BIT [512Kx8/256Kx16] CMOS FLASH MEMORY |
| MX29F400TTC-70 | 制造商:MCNIX 制造商全称:Macronix International 功能描述:4M-BIT [512Kx8/256Kx16] CMOS FLASH MEMORY |
发布紧急采购，3分钟左右您将得到回复。