- 您现在的位置：买卖IC网 > PDF目录11671 > MXB7846EEE+ (Maxim Integrated Products)IC CNTRLR TOUCH RES 16QSOP PDF资料下载
参数资料
| 型号： | MXB7846EEE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/24页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR TOUCH RES 16QSOP |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 类型： | 温度传感器 |
| 输入类型： | 模拟 |
| 输出类型： | 数字 |
| 接口： | 4 线 |
| 电流 - 电源： | 950µA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
| 产品目录页面： | 1424 (CN2011-ZH PDF) |
MXB7846
2.375V to 5.25V, 4-Wire Touch-Screen Controller
with Internal Reference and Temperature Sensor
______________________________________________________________________________________
11
Input Bandwidth and Anti-Aliasing
The ADCs input tracking circuitry has a 25MHz small-
signal bandwidth, so it is possible to digitize high-
speed transient events. To avoid high-frequency sig-
nals being aliased into the frequency band of interest,
anti-alias filtering is recommended.
Analog Input Protection
Internal protection diodes, which clamp the analog input
to VDD and GND, allow the analog input pins to swing
from GND - 0.3V to VDD + 0.3V without damage. Analog
inputs must not exceed VDD by more than 50mV or be
lower than GND by more than 50mV for accurate con-
version. If an off-channel analog input voltage exceeds
the supplies, limit the input current to 50mA. The analog
input pins are ESD protected to ±8kV using the Contact
Discharge method and ±15kV using the Air-Gap
method specified in IEC 61000-4-2.
Touch-Screen Conversion
The MXB7846 provides two conversion methods—differ-
ential and single ended. The SER/
DFR bit in the control
word selects either mode. A logic 1 selects a single-
ended conversion, while a logic 0 selects a differential
conversion.
Differential vs. Single Ended
Changes in operating conditions can degrade the accu-
racy and repeatability of touch-screen measurements.
Therefore, the conversion results representing X and Y
coordinates may be incorrect. For example, in single-
ended measurement mode, variation in the touch-screen
driver voltage drops results in incorrect input reading.
Differential mode minimizes these errors.
Single-Ended Mode
Figure 3 shows the switching matrix configuration for
Y-coordinate measurement in single-ended mode. The
MXB7846 measures the position of the pointing device
by connecting X+ to IN+ of the ADC, enabling Y+ and
Y- drivers, and digitizing the voltage on X+. The ADC
performs a conversion with REF+ = REF and REF- =
GND. In single-ended measurement mode, the bias to
the touch screen can be turned off after the acquisition
to save power. The on-resistance of the X and Y drivers
results in a gain error in single-ended measurement
mode. Touch-screen resistance ranges from 200Ω to
900Ω (depending on the manufacturer), whereas the
on-resistance of the X and Y drivers is 8Ω (typ). Limit
the touch-screen current to less than 50mA by using a
touch screen with a resistance higher than 100Ω. The
resistive-divider created by the touch screen and the
on-resistance of the X and Y drivers result in both an
offset and a gain shift. Also, the on-resistance of the X
and Y drivers does not track the resistance of the touch
screen over temperature and supply. This results in fur-
ther measurement errors.
Differential Measurement Mode
Figure 4 shows the switching matrix configuration for
Y-coordinate measurement. The REF+ and REF- inputs
are connected directly to the Y+ and Y- pins, respec-
tively. Differential mode uses the voltage at the Y+ pin
as the REF+ voltage and voltage at the Y- pin as REF-
voltage. This conversion is ratiometric and independent
of the voltage drop across the drivers and variation in
the touch-screen resistance. In differential mode, the
touch screen remains biased during the acquisition and
conversion process. This results in additional supply
current and power dissipation during conversion when
compared to the absolute measurement mode.
PEN Interrupt Request (
PENIRQ)
Figure 5 shows the block diagram for the
PENIRQ func-
tion. When used,
PENIRQ requires a 10kΩ to 100kΩ
pullup to +VDD. If enabled, PENIRQ goes low whenever
the touch screen is touched. The
PENIRQ output can
be used to initiate an interrupt to the microprocessor,
which can write a control word to the MXB7846 to start
a conversion.
Figure 6 shows the timing diagram for the
PENIRQ pin
function. The diagram shows that once the screen is
touched while
CS is high, the PENIRQ output goes low
after a time period indicated by tTOUCH. The tTOUCH
value changes for different touch-screen parasitic
capacitance and resistance. The microprocessor
receives this interrupt and pulls
CS low to initiate a con-
version. At this instant, the
PENIRQ pin should be
masked, as transitions can occur due to a selected
input channel or the conversion mode. The
PENIRQ pin
functionality becomes valid when either the last data bit
is clocked out, or
CS is pulled high.
Touch-Pressure Measurement
The MXB7846 provides two methods for measuring the
pressure applied to the touch screen (Figure 7). By
measuring RTOUCH, it is possible to differentiate
between a finger or stylus in contact with the touch
screen. Although 8-bit resolution is typically sufficient,
the following calculations use 12-bit resolution demon-
strating the maximum precision of the MXB7846.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6682MUA+ | IC THERMISTOR TO DGTL 8UMAX |
| VI-BTK-IW-F3 | CONVERTER MOD DC/DC 40V 100W |
| VI-BTJ-IX-F2 | CONVERTER MOD DC/DC 36V 75W |
| 2081202-1 | CONN PLUG SMA CRIMP RG402 |
| DS1876T+ | IC CTRLR SFP DUAL LDD 28TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MXB7846EEE+ | 功能描述:触摸屏转换器和控制器 2.375-5.25V 4-Wire Touch-Screen Ctlr RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MXB7846EEE+T | 功能描述:触摸屏转换器和控制器 2.375-5.25V 4-Wire Touch-Screen Ctlr RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MXB7846EEE-T | 功能描述:触摸屏转换器和控制器 RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MXB7846EUE | 功能描述:触摸屏转换器和控制器 RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MXB7846EUE+ | 功能描述:触摸屏转换器和控制器 2.375-5.25V 4-Wire Touch-Screen Ctlr RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
发布紧急采购，3分钟左右您将得到回复。