- 您现在的位置：买卖IC网 > PDF目录19927 > MXD1210ESA+ (Maxim Integrated)IC CNTRLR NVRAM 8-SOIC PDF资料下载
参数资料
| 型号： | MXD1210ESA+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 5/9页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR NVRAM 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 控制器类型： | 非易失性 RAM |
| 电源电压： | 4.75 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
MXD1210
Nonvolatile RAM Controller
_______________________________________________________________________________________
5
_______________________________________________________________________________________
5
Detailed Description
Main Functions
The MXD1210 executes five main functions to perform
reliable RAM operation and battery backup (see the
Typical Operating Circuit and Figure 1):
1) RAM Power-Supply Switch: The switch directs
power to the RAM from the incoming supply or
from the selected battery, whichever is at the
greater voltage. The switch control uses the same
criterion to direct power to MXD1210 internal cir-
cuitry.
2) Power-Failure Detection: The write-protection
function is enabled when a power failure is
detected. The power-failure detection range
depends on the state of the TOL pin as follows:
Power-failure detection is independent of the bat-
tery-backup function and precedes it sequentially
as the power-supply voltage drops during a typi-
cal power failure.
3) Write Protection: This holds the chip-enable out-
put (
CEO) to within 0.2V of VCCI or of the selected
battery, whichever is greater. If the chip-enable
input (
CE) is low (active) when power failure is
detected, then
CEO is held low until CE is brought
high, at which time
CEO is gated high for the
duration of the power failure. The preceding
sequence completes the current RD/WR cycle,
preventing data corruption if the RAM access is a
WR cycle.
4) Battery Redundancy: A second battery is option-
al. When two batteries are connected, the
stronger battery is selected to provide RAM back-
up and to power the MXD1210. The battery-selec-
tion circuitry remains active while in the
battery-backup mode, selecting the stronger bat-
tery and isolating the weaker one. The battery-
selection activity is transparent to the user and
the system. If only one battery is connected, the
second battery input should be grounded.
5) Battery-Status Warning: This notifies the system
when the stronger of the two batteries measures ≤
2.0V. Each time the MXD1210 is repowered (VCCI
> VCCTP) after detecting a power failure, the bat-
tery voltage is measured. If the battery in use is
low, following the MXD1210 recovery period, the
device issues a warning to the system by inhibit-
ing the second memory cycle. The sequence is
as follows:
First access: read memory location n, loc(n) = x
Second access: write memory location n,
loc(n) = complement (x)
Third access: read memory location n, loc(n) = ?
If the third access (read) is complement (x), then the
battery is good; otherwise the battery is not good.
Return to loc(n) = x following the test sequence.
Freshness-Seal Mode
The freshness-seal mode relates to battery longevity
during storage rather than directly to battery backup.
This mode is activated when the first battery is con-
nected, and is defeated when the voltage at VCCI first
exceeds VCCTP. In the freshness-seal mode, both bat-
teries are isolated from the system; that is, no current is
drained from either battery, and the RAM is not pow-
ered by either battery. This means that batteries can be
installed and the system can be held in inventory with-
out battery discharge. The positive edge rate at
VBATT1 and VBATT2 should exceed 0.1V/s. The bat-
teries will maintain their full shelf life while installed in
the system.
Battery Backup
The
Typical Operating Circuit shows the MXD1210 con-
nected to write-protect the RAM when VCC is less than
4.75V, and to provide battery backup to the supply.
CONDITION
VCCTP RANGE (V)
TOL = GND
4.75 to 4.50
TOL = VCCO
4.50 to 4.25
相关PDF资料 |
PDF描述 |
|---|---|
| DS1210N+ | IC CONTROLLER CHIP NV IND 8-DIP |
| RZB110DHHN | CONN EDGE DUAL .050 DIP 220 POS |
| RMC28DRAI-S734 | CONN EDGECARD 56POS .100 R/A PCB |
| 3415-0002 | CARD EDGE CONN 50POS W/FLANGE |
| RBM06DRMN-S288 | CONN EDGECARD 12POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MXD1210ESA+ | 功能描述:IC CNTRLR NVRAM 8-SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 - 控制器 系列:- 标准包装:45 系列:- 控制器类型:静态 RAM（SRAM） 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| MXD1210ESA+T | 功能描述:IC CNTRLR NVRAM 8-SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 - 控制器 系列:- 标准包装:45 系列:- 控制器类型:静态 RAM（SRAM） 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| MXD1210ESA-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MXD1210EWE | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MXD1210EWE+ | 功能描述:IC CNTRLR NVRAM 16-SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 - 控制器 系列:- 标准包装:45 系列:- 控制器类型:静态 RAM（SRAM） 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。