参数资料
| 型号： | NCP1002PG |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/14页 |
| 文件大小： | 0K |
| 描述： | IC OFFLINE SWIT PWM UVLO HV 8DIP |
| 产品变化通告： | Product Obsolescence 01/Jul/2009 |
| 标准包装： | 50 |
| 输出隔离： | 隔离 |
| 频率范围： | 90kHz ~ 115kHz |
| 输入电压： | 7.5 V ~ 10 V |
| 输出电压： | 700V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 其它名称： | NCP1002PGOS |
NCP1000, NCP1001, NCP1002
AUX min
Rs max =
CC1max
AUX max
min
1.0mA + I
reliability in overload conditions. Figure 20 shows the
timing waveforms in auto restart mode.
The V CC pin receives its startup power from the high
voltage startup circuit. Once the undervoltage lockout trip
point is exceeded, the high voltage startup circuit turns off,
and the V CC pin receives its power from the auxiliary
winding of the power transformer. Once the converter is
enabled, the V CC voltage will be clamped by the 8.6 V
limiter. Since the voltage limiter will regulate the V CC
voltage at 8.6 V, it must shunt all excess current based on the
input impedance to this pin. A resistor is required between
the auxiliary winding filter capacitor and the V CC pin to
limit the current.
Optocoupler Fail--safe Circuit
The NCP100x has the ability to sense an open optocoupler
and protect the load in the event of a failure. This circuit
operates by sensing the current in the V CC limiter, and
detecting a high current which is an indication of an open
optocoupler.
The V CC pin receives the output of a current source which
is created by the voltage drop between the auxiliary winding
and the V CC limiter across the shunt resistor. The Vcc limiter
will clamp the V CC voltage to approximately 8.6 V. Any
current that is available at this pin, that is not needed for
either the chip bias current, or the opto current is shunted
through this limiter.
The opto fail--safe circuit operates on the premise that
under an open opto condition, the opto current will all be
shunted through the V CC limiter, and the output voltage (and
therefore the auxiliary winding voltage) will increase. The
increase in auxiliary winding voltage will cause an
amplified increase in the current into the V CC pin. To detect
an open opto condition, the current in the limiter is measured
and if it exceeds 10 milliamps, the chip will shut down and
go into burst mode operation. After a shutdown signal, the
optocoupler fail--safe circuit will enable the
divide--by--eight counter and attempt to restart the unit after
every eight V CC cycles.
For this circuit to operate properly, the shunt resistor must
be chosen prudently. There is a range of values for R S that
will determine the operation of this circuit. On one extreme,
a large value of R S will minimize the bias current, which will
have the effect of maximizing efficiency, while reducing the
response to an open optocoupler. The other extreme is the
minimum value of R S, which will maximize the bias current
into the chip and minimize the voltage overshoot in the event
For minimum bias current:
(V ? 8.8 volts)
I
where:
V AUXmin is the minimum expected DC voltage from the
auxiliary winding.
Typically, this voltage will vary between ? 5% to ? 10%
from it’s nominal value.
I CC1max is the maximum rated bias current for the device
used. This value can found in the tables on the data sheet.
For the best optocoupler fail--safe response:
(V ? 7.2 volts)
Rs =
trip
where:
V AUXmax is the maximum expected DC voltage from the
auxiliary winding.
I trip is the minimum trip current for the optocoupler
fail--safe. This information can be found in the tables under
Current Limit and Thermal Protection , as well as in
Figure 12.
The value of R S that is used in the circuit must be between
the two extreme values calculated. Setting it closer to R Smin
will optimize the optocoupler fail--safe feature, while setting
it closer to the R Smax value will minimize the bias current
Thermal Shutdown and Package
The internal Thermal Shutdown block protects the device
in the event that the maximum junction temperature is
exceeded. When activated, typically at 140 ? C, one input of
the Driver is held low to disable the Power Switch Circuit.
Thermal shutdown activation is non--latching and the Power
Switch Circuit is allowed resume operation when the
junction temperature falls below 110 ? C. The thermal
shutdown feature is provided to prevent catastrophic device
failures from accidental overheating. It is not intended to be
used as a substitute for proper heatsinking.
The die in the 8--pin dual--in--line package is mounted on
a special heat tab copper alloy lead frame. The tab consists
of pins 3, 6, 7, 8 is specifically designed to improve the
thermal conduction from the die to the printed circuit board.
This permits the use of standard layout and mounting
practices while having the ability to halve the junction to air
thermal resistance.
of an open optocoupler .
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| NCP1015ST65T3G | IC OFFLINE SWIT SMPS CM SOT223 |
| NCP1034DR2G | IC REG CTRLR BUCK PWM VM 16-SOIC |
| NCP1086D2TADJR4G | IC REG LDO ADJ 1.5A D2PAK-3 |
| NCP1117LPST18T3G | IC REG LDO 1.8V 1A SOT-223-4 |
| NCP112PG | IC SUPERVISORY PS DESKTOP 14DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1002T | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| NCP100ALPRPG | 功能描述:基准电压& 基准电流 ANA SUB IV SHUNT REG RoHS:否 制造商:STMicroelectronics 产品:Voltage References 拓扑结构:Shunt References 参考类型:Programmable 输出电压:1.24 V to 18 V 初始准确度:0.25 % 平均温度系数（典型值）:100 PPM / C 串联 VREF - 输入电压（最大值）: 串联 VREF - 输入电压（最小值）: 分流电流（最大值）:60 mA 最大工作温度:+ 125 C 封装 / 箱体:SOT-23-3L 封装:Reel |
| NCP100SNT1 | 功能描述:基准电压& 基准电流 0.9-6V 0.1-20mA RoHS:否 制造商:STMicroelectronics 产品:Voltage References 拓扑结构:Shunt References 参考类型:Programmable 输出电压:1.24 V to 18 V 初始准确度:0.25 % 平均温度系数（典型值）:100 PPM / C 串联 VREF - 输入电压（最大值）: 串联 VREF - 输入电压（最小值）: 分流电流（最大值）:60 mA 最大工作温度:+ 125 C 封装 / 箱体:SOT-23-3L 封装:Reel |
| NCP100SNT1G | 功能描述:基准电压& 基准电流 0.9-6V 0.1-20mA RoHS:否 制造商:STMicroelectronics 产品:Voltage References 拓扑结构:Shunt References 参考类型:Programmable 输出电压:1.24 V to 18 V 初始准确度:0.25 % 平均温度系数（典型值）:100 PPM / C 串联 VREF - 输入电压（最大值）: 串联 VREF - 输入电压（最小值）: 分流电流（最大值）:60 mA 最大工作温度:+ 125 C 封装 / 箱体:SOT-23-3L 封装:Reel |
| NCP1010 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Self-Supplied Monolithic Switcher for Low Standby- Power Offline SMPS |
发布紧急采购，3分钟左右您将得到回复。