- 您现在的位置：买卖IC网 > PDF目录19530 > NCP1010AP100 (ON Semiconductor)IC OFFLINE SWIT SMPS CM OVP 8DIP PDF资料下载
参数资料
| 型号： | NCP1010AP100 |
| 厂商： | ON Semiconductor |
| 文件页数： | 17/24页 |
| 文件大小： | 0K |
| 描述： | IC OFFLINE SWIT SMPS CM OVP 8DIP |
| 产品变化通告： | LTB Notification 03/Jan/2008 |
| 标准包装： | 1,000 |
| 输出隔离： | 隔离 |
| 频率范围： | 90kHz ~ 110kHz |
| 输入电压： | 8.5 V ~ 10 V |
| 输出电压： | 700V |
| 功率（瓦特）： | 19W |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm），7 引线 |
| 供应商设备封装： | 7-PDIP |
| 包装： | 管件 |
NCP1010, NCP1011, NCP1012, NCP1013, NCP1014
? ? ?
1
1 +
Tsw = Lp
·
2 · Fsw · [Pout · (Vr2 + 2 · Vr · Vin + Vin2)]
(eq. 22) where Vinmin
Lpmax =
which lets us calculate the RMS
Ip · Lp
d =
? d3
The Flyback transfer formula dictates that:
η 2
Pout = 1 · Lp · Ip2 · Fsw (eq. 19) which, by extracting
Ip and plugging into Equation 19, leads to:
2 · Pout
η · Fsw · Lp Vin N · (Vout + Vf)
(eq. 20)
Extracting Lp from Equation 20 gives:
(Vin · Vr)2 · η
Lpcritical =
(eq. 21) , with Vr = N . (Vout + Vf) and η the efficiency.
If Lp critical gives the inductance value above which
DCM operation is lost, there is another expression we can
write to connect Lp, the primary peak current bounded by
the NCP101X and the maximum duty--cycle that needs to
stay below 50%:
DCmax · Vinmin · Tsw
Ipmax
corresponds to the lowest rectified bulk voltage, hence the
longest ton duration or largest duty--cycle. Ip max is the
available peak current from the considered part, e.g. 350 mA
typical for the NCP1013 (however, the minimum value of
this parameter shall be considered for reliable evaluation).
Combining Equations 21 and 22 gives the maximum
theoretical power you can pass respecting the peak current
capability of the NCP101X, the maximum duty--cycle and
the discontinuous mode operation:
Pmax : = Tsw2 · Vinmin2 · Vr2 · η ·
Fsw
(2 · Lpmax · Vr2 + 4 · Lpmax · Vr · Vinmin
+ 2 · Lpmax · Vinmin2) (eq. 23)
From Equation 22 we obtain the operating duty--cycle
(eq. 24)
Vin · Tsw
current circulating i n the MOSFET:
IdRMS = Ip · (eq. 25) . From this equation, we
obtain the average dissipation in the MOSFET:
Example 1. A 12 V 7.0 W SMPS operating on a large
mains with NCP101X:
Vin = 100 Vac to 250 Vac or 140 Vdc to 350 Vdc once
rectified, assuming a low bulk ripple
Efficiency = 80%
Vout = 12 V, Iout = 580 mA
Fswitching = 65 kHz
Ip max = 350 mA – 10% = 315 mA
Applying the above equations leads to:
Selected maximum reflected voltage = 120 V
with Vout = 12 V, secondary drop = 0.5 V ? Np:Ns = 1:0.1
Lp critical = 3.2 mH
Ip = 292 mA
Duty--cycle worse case = 50%
Idrain RMS = 119 mA
P MOSFET = 354 mW at R DSon = 24 Ω (T J > 100 ? C)
P DSS = 1.1 mA x 350 V = 385 mW, if DSS is used
Secondary diode voltage stress = (350 x 0.1) + 12 = 47 V
(e.g. a MBRS360T3, 3.0 A/60 V would fit)
Example 2. A 12 V 16 W SMPS operating on narrow
European mains with NCP101X:
Vin = 230 Vac ? 15%, 276 Vdc for Vin min to 370 Vdc
once rectified
Efficiency = 80%
Vout = 12 V, Iout = 1.25 A
Fswitching = 65 kHz
Ip max = 350 mA – 10% = 315 mA
Applying the equations leads to:
Selected maximum reflected voltage = 250 V
with Vout = 12 V, secondary drop = 0.5 V ? Np:Ns = 1:0.05
Lp = 6.6 mH
Ip = 0.305 mA
3
Pavg = 1 · Ip2 · d · RDSon
losses shall be added.
(eq. 26)
to which switching
Duty--cycle worse case = 0.47
Idrain RMS = 121 mA
If we stick to Equation 23, compute Lp and follow the
above calculations, we will discover that a power supply
built with the NCP101X and operating from a 100 Vac line
minimum will not be able to deliver more than 7.0 W
continuous, regardless of the selected switching frequency
(however the transformer core size will go down as
Fswitching is increased). This number increases
significantly when operated from a single European mains
(18 W). Application note AND8125/D, “Evaluating the
Power Capability of the NCP101X Members” details how
to assess the available power budget from all the NCP101X
series.
P MOSFET = 368 mW at R DSon = 24 Ω (T J > 100 ? C)
P DSS = 1.1 mA x 370 V = 407 mW, if DSS is used below an
ambient of 50 ? C.
Secondary diode voltage stress = (370 x 0.05) + 12 = 30.5 V
(e.g. a MBRS340T3, 3.0 A/40 V)
Please note that these calculations assume a flat DC rail
whereas a 10 ms ripple naturally affects the final voltage
available on the transformer end. Once the Bulk capacitor has
been selected, one should check that the resulting ripple (min
Vbulk?) is still compatible with the above calculations. As an
example, to benefit from the largest operating range, a 7.0 W
board was built with a 47 m F bulk capacitor which ensured
discontinuous operation even in the ripple minimum waves.
http://onsemi.com
17
相关PDF资料 |
PDF描述 |
|---|---|
| EPM1270T144C3 | IC MAX II CPLD 1270 LE 144-TQFP |
| REC3-1215SRW/H2/A | CONV DC/DC 3W 9-18VIN 15VOUT |
| EBM24DSXN | CONN EDGECARD 48POS DIP .156 SLD |
| RCB60DHAD | CONN EDGECARD 120PS R/A .050 DIP |
| VI-B10-CY-F1 | CONVERTER MOD DC/DC 5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1010AP100G | 功能描述:电流型 PWM 控制器 Low Standby Power Monolithic Switcher RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1010AP130 | 功能描述:电流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1010AP130G | 功能描述:电流型 PWM 控制器 Low Standby Power Monolithic Switcher RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1010ST100T3 | 功能描述:电流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1010ST100T3G | 功能描述:电流型 PWM 控制器 Low Standby Power Monolithic Switcher RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。