- 您现在的位置：买卖IC网 > PDF目录19530 > NCP1010AP100 (ON Semiconductor)IC OFFLINE SWIT SMPS CM OVP 8DIP PDF资料下载
参数资料
| 型号： | NCP1010AP100 |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | IC OFFLINE SWIT SMPS CM OVP 8DIP |
| 产品变化通告： | LTB Notification 03/Jan/2008 |
| 标准包装： | 1,000 |
| 输出隔离： | 隔离 |
| 频率范围： | 90kHz ~ 110kHz |
| 输入电压： | 8.5 V ~ 10 V |
| 输出电压： | 700V |
| 功率（瓦特）： | 19W |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm），7 引线 |
| 供应商设备封装： | 7-PDIP |
| 包装： | 管件 |
NCP1010, NCP1011, NCP1012, NCP1013, NCP1014
APPLICATION INFORMATION
Introduction
The NCP101X offers a complete current--mode control
solution (actually an enhanced NCP1200 controller section)
together with a high--voltage power MOSFET in a
monolithic structure. The component integrates everything
needed to build a rugged and low--cost Switch--Mode Power
Supply (SMPS) featuring low standby power. The Quick
Selection Table on Page 2, details the differences between
references, mainly peak current setpoints and operating
frequency.
No need for an auxiliary winding: ON Semiconductor
Very High Voltage Integrated Circuit technology lets you
supply the IC directly from the high--voltage DC rail. We call
it Dynamic Self--Supply (DSS). This solution simplifies the
transformer design and ensures a better control of the SMPS
in difficult output conditions, e.g. constant current
operations. However, for improved standby performance,
an auxiliary winding can be connected to the V CC pin to
disable the DSS operation.
Short--circuit protection: By permanently monitoring the
feedback line activity, the IC is able to detect the presence of
a short--circuit, immediately reducing the output power for
No acoustic noise while operating: Instead of skipping
cycles at high peak currents, the NCP101X waits until the
peak current demand falls below a fixed 1/4 of the maximum
limit. As a result, cycle skipping can take place without
having a singing transformer ? You can thus select cheap
magnetic components free of noise problems.
SPICE model: A dedicated model to run transient
cycle--by--cycle simulations is available but also an
averaged version to help close the loop. Ready--to--use
templates can be downloaded in OrCAD’s PSpice, and
INTUSOFT’s IsSpice4 from ON Semiconductor web site,
NCP101X related section.
Dynamic Self--Supply
When the power supply is first powered from the mains
outlet, the internal current source (typically 8.0 mA) is
biased and charges up the V CC capacitor from the drain pin.
Once the voltage on this V CC capacitor reaches the VCC OFF
level (typically 8.5 V), the current source turns off and
pulses are delivered by the output stage: the circuit is awake
and activates the power MOSFET. Figure 13 details the
internal circuitry.
a total system protection. Once the short has disappeared, the
controller resumes and goes back to normal operation.
Fail--safe optocoupler and OVP: When an auxiliary
winding is connected to the V CC pin, the device stops its
internal Dynamic Self--Supply and takes its operating power
from the auxiliary winding. A 8.7 V active clamp is
connected between V CC and ground. In case the current
injected in this clamp exceeds a level of 7.4 mA (typical),
the controller immediately latches off and stays in this
Vref OFF = 8.5 V
Vref ON = 7.5 V
Vref Latch = 4.7 V*
+
--
Internal Supply
Drain
Startup Source
V CC
position until V CC cycles down to 3.0 V (e.g. unplugging the
converter from the wall). By adjusting a limiting resistor in
series with the V CC terminal, it becomes possible to
implement an overvoltage protection function, latching off
the circuit in case of broken optocoupler or feedback loop
+
Vref
VCC OFF
+200 mV
(8.7 V Typ.)
+
CV CC
problems.
Low standby--power: If SMPS naturally exhibits a good
efficiency at nominal load, it begins to be less efficient when
the output power demand diminishes. By skipping unneeded
*In fault condition
Figure 13. The Current Source Regulates V CC
by Introducing a Ripple
switching cycles, the NCP101X drastically reduces the
power wasted during light load conditions. An auxiliary
winding can further help decreasing the standby power to
extremely low levels by invalidating the DSS operation.
Typical measurements show results below 80 mW @
230 Vac for a typical 7.0 W universal power supply.
http://onsemi.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| EPM1270T144C3 | IC MAX II CPLD 1270 LE 144-TQFP |
| REC3-1215SRW/H2/A | CONV DC/DC 3W 9-18VIN 15VOUT |
| EBM24DSXN | CONN EDGECARD 48POS DIP .156 SLD |
| RCB60DHAD | CONN EDGECARD 120PS R/A .050 DIP |
| VI-B10-CY-F1 | CONVERTER MOD DC/DC 5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1010AP100G | 功能描述:电流型 PWM 控制器 Low Standby Power Monolithic Switcher RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1010AP130 | 功能描述:电流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1010AP130G | 功能描述:电流型 PWM 控制器 Low Standby Power Monolithic Switcher RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1010ST100T3 | 功能描述:电流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1010ST100T3G | 功能描述:电流型 PWM 控制器 Low Standby Power Monolithic Switcher RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。