参数资料
型号: NCP1015AP100G
厂商: ON Semiconductor
文件页数: 8/22页
文件大小: 0K
描述: IC OFFLINE SWIT SMPS CM 8DIP
标准包装: 1,000
输出隔离: 隔离
频率范围: 90kHz ~ 110kHz
输入电压: 8.1 V ~ 10 V
输出电压: 700V
功率(瓦特): 19W
工作温度: -40°C ~ 125°C
封装/外壳: 8-DIP(0.300",7.62mm),7 引线
供应商设备封装: 7-PDIP
包装: 管件
产品目录页面: 1127 (CN2011-ZH PDF)
其它名称: NCP1015AP100GOS
NCP1015
8.5V
8.00
6.00
4.00
Vcc
7.5V
2.00
Device
internally
pulses
0
Startup period
Figure 13. The Charge/Discharge Cycle over a 10 m F V CC Capacitor
ICC1 @ t startup
D V
4V
As one can see, the V CC capacitor shall be dimensioned to
offer an adequate startup time, i.e. ensure regulation is
reached before V CC crosses 7.5 V (otherwise the part enters
the fault condition mode). If we know that D V = 1 V and
ICC1 is 1.2 mA (for instance we selected a 11 W device
switching at 65 kHz), then the V CC capacitor can be
calculated using:
C w (eq. 1)
Let’s suppose that the SMPS needs 10 ms to startup, then
we will calculate C to offer a 15 ms period. As a result, C
the so ? called latch ? off level, where the current source
activates again to attempt a new re ? start. If the error has
gone, the IC automatically resumes its operation. If the
default is still there, the IC pulses during 8.5 V down to 7.5 V
and enters a new latch ? off phase. The resulting burst
operation guarantees a low average power dissipation and
lets the SMPS sustain a permanent short ? circuit. Figure 14
presents the corresponding diagram:
Current Sense
Information
should be greater than 18 m F thus the selection of a 33 m F /
16 V capacitor is appropriate.
Short Circuit Protection
The internal protection circuitry involves a patented
arrangement that permanently monitors the assertion of an
internal error flag. This error flag is, in fact, a signal that
FB
Division
Max
Ip
V CC
+
?
V CC(on)
To
Latch
Reset
instructs the controller that the internal maximum peak
current limit is reached. This naturally occurs during the
startup period (V out is not stabilized to the target value) or
when the optocoupler LED is no longer biased, e.g in a
short ? circuit condition or when the feedback network is
broken. When the DSS normally operates, the logic checks
Clamp
Active?
Flag
for the presence of the error flag every time V CC crosses
V CC(on) . If the error flag is low (peak limit not active) then
the IC works normally. If the error signal is active, then the
NCP1015 immediately stops the output pulses, reduces its
internal current consumption and does not allow the startup
source to activate: V CC drops toward ground until it reaches
Figure 14. Simplified NCP1015 Short ? Circuit
Detection Circuitry
The protection burst duty ? cycle can easily be computed
through the various timing events as portrayed by Figure 15:
http://onsemi.com
8
相关PDF资料
PDF描述
EMM40DRMH-S288 CONN EDGECARD 80POS .156 EXTEND
1-1871058-3 PCI EXPRESS CONN EON 98P L=3.25
RCC13DCAD CONN EDGECARD 26POS R/A .100 EXT
EMM40DRMD-S288 CONN EDGECARD 80POS .156 EXTEND
THJE336K035RJN CAP TANT 33UF 35V 10% 2917
相关代理商/技术参数
参数描述
NCP1015ST100T3G 功能描述:电流型 PWM 控制器 MONOLTHC SWTCHR SMPS RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
NCP1015ST65T3G 功能描述:电流型 PWM 控制器 MONOLTHC SWTCHR SMPS RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
NCP102 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Low Dropout Linear Regulator Controller
NCP1027 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Power Factor Controllers
NCP1027ATXEVB 制造商:ON Semiconductor 功能描述:NCP1027 10W STANDBY ATX - Bulk