参数资料
型号: NCP1030GEVB
厂商: ON Semiconductor
文件页数: 2/19页
文件大小: 0K
描述: EVAL BOARD FOR NCP1030
设计资源: NCP1030EVB Gerber Files
NCP1030EVB Schematic
NCP1030EVB BOM
标准包装: 1
主要目的: 特殊用途 DC/DC,以太网供电(POE)
输出及类型: 1,隔离
输出电压: 12V
电流 - 输出: 170mA
输入电压: 36 ~ 76V
稳压器拓扑结构: 回扫
频率 - 开关: 250kHz
板类型: 完全填充
已供物品:
已用 IC / 零件: NCP1030
其它名称: NCP1030EVBOS
NCP1030EVBOS-ND
NCP1030, NCP1031
GND
R SENSE
Disable
V DRAIN
Internal Bias
I 1
Current Limit
Comparator
LEB
+
7.5 V/10 V
--
I START
V CC
--
I
O
--
Reset Q
R
Reset
Q
--
C T
VFB
10 V
I 2 = 3I 1
Error Amplifier
--
+
10 V +
2.5 V
C T Ramp
+
3.0 V/3.5 V --
One Shot
Pulse
--
+
PWM Comparator
+
50 mV
S
Dominant
Latch
PWM Latch
Thermal
Shutdown
S
Dominant
Latch
R
+
--
10 V
2.5 V
16 V
+
--
+
6.5 V
10 V
10 V
UV
OV
COMP
4.5 V
2 k Ω
10 V
Figure 1. NCP1030/31 Functional Block Diagram
FUNCTIONAL PIN DESCRIPTION
Pin
1
2
3
4
5
6
7
8
Name
GND
C T
V FB
COMP
OV
UV
V CC
V DRAIN
Function
Ground
Oscillator Frequency
Selection
Feedback Input
Error Amplifier Compensation
Line Overvoltage Shutdown
Line Undervoltage Shutdown
Supply Voltage
Power Switch and
Startup Circuits
Description
Ground reference pin for the circuit.
An external capacitor connected to this pin sets the oscillator frequency up to 1 MHz.
The oscillator can be synchronized to a higher frequency by charging or discharging
C T to trip the internal 3.0 V/3.5 V comparator. If a fault condition exists, the power
switch is disabled and the frequency is reduced by a factor of 7.
The regulated voltage is scaled down to 2.5 V by means of a resistor divider.
Regulation is achieved by comparing the scaled voltage to an internal 2.5 V reference.
Requires external compensation network between COMP and V FB pins. This pin is
effectively grounded if faults are present.
Line voltage (V in ) is scaled down using an external resistor divider such that the OV
voltage reaches 2.5 V when line voltage reaches its maximum operating voltage.
Line voltage is scaled down using an external resistor divider such that the UV
voltage reaches 2.5 V when line voltage reaches its minimum operating voltage.
This pin is connected to an external capacitor for energy storage. During Turn--On, the
startup circuit sources current to charge the capacitor connected to this pin. When the
supply voltage reaches V CC(on) , the startup circuit turns OFF and the power switch is
enabled if no faults are present. An external winding is used to supply power after
initial startup to reduce power dissipation. V CC should not exceed 16 V.
This pin directly connects the Power Switch and Startup Circuits to one of the
transformer windings. The internal High Voltage Power Switch Circuit is connected
between this pin and ground. V DRAIN should not exceed 200 V.
http://onsemi.com
2
相关PDF资料
PDF描述
RBC18DREN CONN EDGECARD 36POS .100 EYELET
R1D-2405/HP CONV DC/DC 1W 24VIN +/-05VOUT
MAX6034BEXR30+T IC VREF SERIES PREC 3V SC-70-3
395-060-540-204 CARD EDGE 60POS DL .100X.200 BLK
1486B24 WIRING TROUGH STL 2.5X2.5X24" GR
相关代理商/技术参数
参数描述
NCP1031 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Low Power PWM Controller with On−Chip Power Switch and Startup Circuits for 48V Telecom Systems
NCP1031DR2 功能描述:直流/直流开关转换器 Bias Regulator RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
NCP1031DR2G 功能描述:直流/直流开关转换器 Bias Regulator w/On Chip Power RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
NCP1031MNTXG 功能描述:电流型 PWM 控制器 ANA BIAS REGLTR CNTR RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
NCP1031POEEVB 功能描述:电源管理IC开发工具 EVAL BRD REGULATOR CONTROLLER RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V